AUX 1
Type: Posts; User: msdeltaguy
AUX 1
Can someone give me an overview of what is needed to have speed control within MACH3 for one of these 2.2Kw chinese Hyuanyang spindle packages? I am helping a friend out on this one.
Are there...
guess nobody wants to help us out LOL
nobody ????
Trying to get a remote POT working and run into a little problem.
I have a 10K Ohm POT dial wired into my VFD and the settings changed on my VFD to "remote" and I have somewhat of an issue. The...
that enplanes it..... I figured the spindle was pulling more than 2 amps. Hey thanks for the information about the cable also. So far I haven't had any issues with my cut extension cord power cable...
Hello all!
I purchased a chinese 2.2Kw spindle and VFD package and was wondering about power cable. Right now I have an old 12/3 extension cord cut using as power cable and a16awg Green ground...
When i put my meter to measure Ohms im getting a constant reading of 1.7 between the pins you have asked me to measure across. Here is a picture with my cap off the spindle. absolutely no ground...
So put my Fluke in Ohms and test pin to pin like you have suggested then report back the results?
ER11 only will accept a max tool shank size of .276 or 7mm. You will need to either find some larger bits with quarter inch shafts which i really dont recommend or get you a new spindle that's at...
I was called into work shortly after I woke so its going to be a while before I can perform the test. It will be later today but I will do as you have instructed and update the thread with the results
im ready its 4am here in Mississippi LOL
More info needed. What kind of spindle do you have? for example if you have a 2.2Kw with an ER 20 then you can accept half inch bits you will have to get an ER20 1/2'' collet
Yep. Ive checked the VFD several times. Everything runs super good but when i grab my CNC table in certain areas it will shock the hell out of me. Obviously the external spindle case is being...
Thanks for the video but I have all that correct so far.
When cutting. when cutting with a 3/4 end mill under a decent load (hardwood with a .25inch pass depth) the highest ive seen it get is about 1.9amps @ 18k RPM. I would figure that it would jump up...
With it wired up like stated below:
U=Pin 1
V=Pin 2
W=Pin 3
I just reconnected the earth ground to my table and when I hit run on the VFD i hear a pop from the spindle and the VFD goes into...
I have a fluke T87 will this be sufficient ? If so tell me what I need to test. I just rewired my spindle like this. Mine was in a different order using pins 1,2,3
U=Pin 1
V=Pin 2
W=Pin 3
yes please send a picture.
Also when running full speed my VFD is only showing 1.6AMP does this seem right? I figured it would run higher that that being an 8 amp spindle.
I have one of those amazon chinese spindle/VFD combos 2.2Kw and was wondering what is needed to control on and off as well as spindle speed within flashcut CNC? I have the 2.5a micro cnc controller
Have a problem I need some help with.
Bought a chinese spindle and VFD 2.2Kw and have a voltage issue. Seems that voltage is leaking and when i touch my cnc table at time i get shocked. I tried...
Thanks for the info i will give that a try. I'm not using any of the output plugs so I will try what you suggested.
I have the USB compact cnc signal generator and need help with how to control an external device. I recently added a water cooled spindle and would like to automate the on/off of the water pump. I...
Attached is the 3 axis and 4 axis flashcut cnc post processor I use everyday with fusion 360. works like a charm.
as for the G54-G59 there is an option in the flashcut software to ignore G54-G59...
Thanks for taking the time to do this. I am about to check it out now.
Yes. I have ultimate. I have attached what i have come up with thus far. please feel free to post your file because i would love to see other toolpathing strategies
I thought these 2.2kw water cooled spindles would operate lower than 6000RPM? Reason I purchased it was to mill aluminum at lower speeds.
I did as you suggested and changed the PD002 to 1 and not the Pot know works but I need to adjust the range. Right now when i turn the knob to the lowest setting the spindly will only ramp down to...
Ok, I figured out the problem with PD003. I put in all the settings that you have listed below exactly as you have listed them. When I hit RUN the spindle ramps up to 24,000RPM no matter where I have...
Just received my replacement kit that I ordered overnight from amazon since the first one burned up. Forst thing I do is reset back to factory default PD013 setting 8 then powered down. I am starting...