sorry for confusion it,s a bridgeport 2 r2c3 i have a hobby shop in my garage
Type: Posts; User: Dar
sorry for confusion it,s a bridgeport 2 r2c3 i have a hobby shop in my garage
hi everyone i have a problem. my bridgeport2 r2c3 screen rolls and i can,t read it.does anybody have one to sell or is it possible to replace it with a modern flat screen thanks for any help
i had a power spike and machine went down. when i restarted it screen shows y measuring system defective. we traced it to the light emiting diode
sem mt-30r4-58 tack lamp.does any one know where...
now i have a problem i,ve never had before. while running the mill in manual[heavy cut] my wife turned on air conditioning spindle stopped.i turned off power and checked fuse box.everything was...
sorry its been so long since i,ve been here.i had a rough year.one of my son in laws passed.shortly before that i had a quad bypass they said it would take ayear to recover.so half way through my...
i have a bp 2 and had a similar problem wouldn,t take a program untill i powered down and shut pc off when i turned both on again it would take the program. good luck.if my machine doesn,t take a...
on my 145 after you hit cycle def and insert info you have to call the cycle. or it will do exactly what your describing. maybe yours is the same. my 2 cents Dar
with a bp you can adjust the head both ways. but i have a bp2 so if i have that problem i have to shim tha head BIG JOB. you are going to have to do the same good luck
...
hi beerfizz
it has been my experience when this happens your z axis is out of plumb and you need to trammel the head
where are you in michigan? im in Flint
Dar
sounds to me like you shouldremove the ball end mill and use a sq end . ball end mills have a lot of surface area.how can you face with a ball end mill anyway???? Dar
im looking for 3/16 pvc rod 130 inches long. i looked everywhere i could think of but the longest i find is 10 feet. a while ago i read that some one was talking about a small extruder for their shop...
you could also hang an extra trolly with threaded shaft hanging down. then tap a hole in plate welded to pipe. slide trolly where you want it and screw pipe down to extend to floor for extra support....
you should be careful with this tern. remember
x is the unknown
spert is a drip under pressure
expert = unknown drip under pressure
...
thanks to everyone especially bborg the no handshake one worked. sure is hard to solder wires into those little bitty pins
Dar
if you don,t read the paper your uninformed if you do read it your misinformed
Mark Twain
as most of you know i don,t know what im doing most of the time, but i,ll keep blundering along. i need to make a rs232 cable but the diagram in the book goes from a 25 pin to a 25 pin so how do i do...
does anyone have the correct wiring for the rs232 cable when going from a25 pin machine to a 9 pin pc. heidenhain tnc145 on series 2 r2c3. i can,t even read those little numbers without a magnifier....
thank guys i,ll give that a try
i went to heidenhain site but wasn,t able to find it. i was hopping we were just pushing the wrong buttons to make it transfer.
maybe this will help?
bp series 2 r2c3
heidenhain tnc145
ez cam
9 pin connector on pc
cable made using manual discription
does this help?
Dar
i need help guys.
baude rate set at2400.
made up 232 cable
wont transfer program
[extin/output not ready]
had machine in edit . is there...
i made some of these dies and punched out model airplane kits for a customer.some of the material i cut was 1/8 ply. i used my hyd. press and a piece of nylon to cut against. it worked real well.
...
thanks for the advice Gus. after checking things again the switch was at fault. took it apart and adjusted it. works fine now. i didn,t want to take it apart untill i knew there were none available. ...
hi guys I don,t know if i,m in trouble again or still probable the latter.
here is the problem my start and run hi and low speed switch will start on the low side but when you release it it...
yes several years ago i had a job making 14in pins from 24ft. pieces of thompson shafting. i used a carbide insert threading tool to initally cut through the case then a parting tool to finish. these...
good luck mike
dar
bp tnc145. table homes right and back. i have never run a cnc before and the guys on this forom have given me a great deal of help.
Dar
hi hmc710. i know very little about my machine but learning every day. on mine the joy stick will move axis [without botton pushed ] only when spindle is running. hope this helps
...
hi all well i finally got a copy of ezcam but no dongle so i,m trying to see if i can draw with it before i spend big to get the whole thing. so what i need is a copy of the manual that tells how to...