502,512 active members
4,718 visitors online
Register for free
Login

Search:

Type: Posts; User: mactec54

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    24
    Views
    70

    Re: 3D Probe - Tri-balls type accuracy & DIY

    30mm dia is not even close to the smallest in the world :wave: Renishaw TP6 basic model is 25mm dia and they make smaller than this

    1um yes anything is possible in the right environment :)
  2. Replies
    17
    Views
    65

    Re: Can I change X,Y,Z zero mid program?

    3D surfaces have nothing to do with X Y Z rapid moves to the start of a part, or a new position move, the Z axes is always moved first then a X Y move the reason you move the Z first is so you don't...
  3. Replies
    24
    Views
    70

    Re: 3D Probe - Tri-balls type accuracy & DIY

    If you have trouble getting the accuracy you need then you could buy this probe https://www.kurokesu.com/shop/TPA2 which has a 2um repeatability
  4. Re: HuangYang VFD driver challenge with Mach3

    The Relay Reset safety circuit will work
  5. Replies
    17
    Views
    65

    Re: Can I change X,Y,Z zero mid program?

    If you just cut and pasted the first program then called it G55 then yes it will have a start position at the first part in it, and will go back to the first part, you have to be careful when you cut...
  6. Replies
    353
    Views
    13,603

    Re: Designing new Router called Maximus

    If they have not given you a quote within 2 to 3 days move on as they are not interested in your work
  7. Replies
    17
    Views
    65

    Re: Can I change X,Y,Z zero mid program?

    Yes correct except you never use a Z axes move when Doing a X Y move, a Z move should always be on a line before a X Y Axes move for obvious reasons

    No it can't be a M55 the control would not...
  8. Replies
    17
    Views
    65

    Re: Can I change X,Y,Z zero mid program?

    Yes that can work but a simple X---- Y------ move to the next position is all that is needed will work also
  9. Re: HuangYang VFD driver challenge with Mach3

    The VFD Drive won't last long if you have it wired like this, the mains power should be on at power up, and stay on until you power off your machine, you use the VFD logic low voltage to control ON /...
  10. Replies
    16
    Views
    65

    Re: I need a manual for VFD ZONCN NZ200

    Your VFD is not different from any other, I'm sure you could do what is needed if you get creative, your sensor would be controlled from your machine control and would output a voltage change to...
  11. Re: DMM Servos with DYN4 Drives on G0704 Random Alarm Issue

    Ok in General Config. for Mach3 look for Lock Rapid if this is checked uncheck it and try again you may be able to lower the rapid moves with the slider on the Mach3 screen under feed rate slider for...
  12. Replies
    9
    Views
    42

    Re: Chinese "for metal" 4-pole spindle

    But not cast Iron

    Just there way of using words as like the plug description Air Plug ( for aviation Plug )
  13. Re: DMM Servos with DYN4 Drives on G0704 Random Alarm Issue

    When you use the Smooth Stepper you should have Mach3 settings Kernel speed at no more than 45Khz ( 25Khz )is the normal setting when using the Smooth Stepper, as this is not in control the Smooth...
  14. Replies
    9
    Views
    42

    Re: Chinese "for metal" 4-pole spindle

    Nothing cast iron about it, if it is the same 2.2Kw spindle then it can run at 3,000 RPM
  15. Replies
    16
    Views
    65

    Re: I need a manual for VFD ZONCN NZ200

    You can attach it here, open a post, go to Advanced scroll down and attach a PDF File
  16. Replies
    16
    Views
    65

    Re: I need a manual for VFD ZONCN NZ200

    Not a very good photo the +10 AVI and Ground Terminals are what your Pot connects to AVI to the center Pot connection there is also a Jumper or switch that needs to be set J2 to AVI it is beside...
  17. Replies
    16
    Views
    65

    Re: I need a manual for VFD ZONCN NZ200

    I need a clear photo of the low voltage terminals

    And no you would not use any of the relay output for a Pot

    Tell me what your VFD is being used for and what it is driving
  18. Replies
    16
    Views
    65

    Re: I need a manual for VFD ZONCN NZ200

    What do you need to know about it I don't have the manual but may be able to help
  19. Replies
    16
    Views
    65

    Re: I need a manual for VFD ZONCN NZ200

    What is the manufactures name
  20. Replies
    9
    Views
    42

    Re: Chinese "for metal" 4-pole spindle

    That would depend on what they term as cutting metal, the spec's where 12,000 RPM to 24,000 RPM this would indicate engraving in metal, which you can do with any of these spindles anyway, it very...
  21. Re: DMM Servos with DYN4 Drives on G0704 Random Alarm Issue

    It is only 400Khz does not compare in any way :wave:
  22. Replies
    9
    Views
    42

    Re: Chinese "for metal" 4-pole spindle

    15 amp at the motor you double that at the VFD Drive input for single phase X 125% ( code requirement for breaker size ) 35A is the closest breaker so your input wiring etc. need to be in that...
  23. Replies
    9
    Views
    42

    Re: Chinese "for metal" 4-pole spindle

    Well you have to decide on what you want 4 Pole or a 2 Pole both spindles are well manufactured


    If you can get the 220v 3.2Kw with ceramic bearings it may be better in the long run, make sure...
  24. Replies
    354
    Views
    983

    Re: GME's New 80/20 CNC Build - My Design

    If you were to modify it at anytime you would fit a aluminum bushing and then this would cut down the diameter of the AF Delrin Bushing size to be made, the pinion end is where a good bearing setup...
  25. Re: DMM Servos with DYN4 Drives on G0704 Random Alarm Issue

    Correct, but a Smooth Stepper is a whole lot better than a UC400 and was designed to use with Mach3 which he can use also with Mach4 if at any time he wants to upgrade
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4