browncoupe,
I looked at your file, the part will cut to the bottom if you remove the boundary
The software is just doing what you tell it to do.I am sure you are just using this as a test part....
Type: Posts; User: Swag
browncoupe,
I looked at your file, the part will cut to the bottom if you remove the boundary
The software is just doing what you tell it to do.I am sure you are just using this as a test part....
V19- 21 has the ability to adjust line width.
I have 21 also, I have saved some .dgn for my
wire edm guy, he is using an old DOS version of BC and is
able to open them.
Mark
In V21 and back you could,I mainly used it for printing.
I haven't found a way to do it in V22-(FKA 2007) on up , I am currently using V23
Mark
If you scroll down farther on the list, there are post for the M series.
Mark
Rob
It is in inches, not metric, I get the same size Jrmach gets.
I imported the file with NCplot,
V21 or V23 wont do it. Here is what I got.
Mark
I changed his mouse, it helped some. I am going to try to upgrade his video drivers, and check for viruses, clean all garbage that build up from the internet.
On occasion the zooming still happens...
I am close to Ernie,
He visits me from time to time.
I am willing to go see him and try to resolve his mouse , I will take one of
my wired ones along also. I know if it is mouse related, we will...
If you are asking for the post to output in the .mx3 format they have a few
post made to do that. look here ...
Ernie,
Its a Vertex says right on it, I found one here
http://www.penntoolco.com/catalog/products/products.cfm?categoryID=7392
Mark
Your Geometry was messed up on the 2 that wouldn't cut, they weren't chains.
You have .250 slots and .1256 R and something else .1272R radius is, if remember correctly, Make them .125 it will be...
Depending on your laptop, use a PCMCIA card, Express Card formats - 54 and 34. An Express Card/34 will fit into an Express Card/54 slot, but not visa versa.
Try a different post, it looks like you are using a lathe post ( assuming this is a mill part), I only see X & Z moves, I didn't see any Y moves in your G code
The verify I don't know,it works here. In your posting you have to choose arc fit, see pic, I did it to your file and went from 23672 lines to 5150 lines of code.
Toby, A friend of mine has a Prototrak that does full 3 X work, he purchased the DNC key.
The last I knew BCC charges a $75.00 transfer fee.
It was a standard fee for all previous versions so I don't see why it would change now.
Actually, I just tried both the 300 dpi didn't work good here,
but even making the line atributes to .005" came out fine !
Steve,
Glad I could help, simple enough.
Mark
Steve
Try on the attributes to change the line width to .010" or .020"
That should print better than a line width of 0.000 It is most likely your
problem.
Mark
If you look at the full ad, is clearly states, buy the first seat, and get the
2nd seat for $1.00
Mark
25.4
Sorry I kinda was stressed and should not have reacted like that!
Mark(chair)
PS look at the post I sent you in PM, It should work for you.
I have a DPM w/AGE 3 control , what issues are you having? I use the basic AGE3 for my 2X mill and a custom post for the 3X mill.
I used this script
all it asks for is the distance across flats. Works
great for me. assuming you are using V21 and back, they
eliminated the scripting in V22 on up
Mark
'HexFlat.bas
Adobe Reader
If I had to Guess it would only be 1
MasterCam
:confused:
Run service code 97 , that should prompt
you to move axis + - then be right. inc set
Mark
I can't take credit for it. I got it from Sorin, and just tweaked it a little,
but it works great, Credit given to were its due !!
:o
I still use it,almost on a daily basis, I trashed 2007/V22 along time back !!
2007/V22 BAD TIME AFTER BAD MONEY. I did find a use for it, I use the disc as a coaster for beer look @ my avitar (pic)
News Flash
Sorry to tell you but it has been past practice, once a new version comes out
the last is no longer supported ! Bobcad has been in business for 23 Yrs.
Now they are on V23,,,,,, looking...