584,830 active members*
5,662 visitors online*
Register for free
Login

Search:

Type: Posts; User: ifixcnc

Page 1 of 17 1 2 3 4

Search: Search took 0.01 seconds.

  1. Re: 6TB control. starting to have problems. Control shutting down middle of run

    If you are lucky it is just a video problem, that can be the CRT unit, or video driver.
    In the fault condition try to jog the machine.
    If you can't change mode or jog, it is likely an control...
  2. Replies
    8
    Views
    1,299

    Re: Displays error 911

    The 900 parameters are specific to the machine. They are they are options from the machine builder. The similar machine 900s may get you running, but some functions may not work. Check the electrical...
  3. Thread: FANUC ALARM 12

    by ifixcnc
    Replies
    2
    Views
    891

    Re: FANUC ALARM 12

    The tag is normally on the side of the IGBT module. You have to remove it to see all sides.
  4. Replies
    14
    Views
    5,814

    Re: FANUC OM-F parameter button wont respond

    Try the 2 keys to the right, under the screen.
  5. Replies
    39
    Views
    25,149

    Re: ALARM 2161 LUBRICATION OIL PRESSURE DOWN

    You will have better luck if you start a new thread.
  6. Thread: Fanuc battery

    by ifixcnc
    Replies
    9
    Views
    12,087

    Re: Fanuc battery

    There is an battery low alarm, and a battery Zero alarm.
    If you have the Low alarm, and change batteries with the power off, you will lose the APC position.
    Batteries are in the yellow Fanuc...
  7. Replies
    2
    Views
    1,368

    Re: Reducing RF Interference

    5th wire goes to the motor case, the other end of that wire,drive’s power supply ground.
    Ground the shield to your electronics control box at the control box end only, the other end of the shield is...
  8. Replies
    9
    Views
    1,403

    Re: Fanuc motherboard repair company needed

    I did not read the original post clearly "after change in both machines screen the crt is blank and no start off the both machines" indeed shows that something in the machine is harming the...
  9. Replies
    9
    Views
    1,403

    Re: Fanuc motherboard repair company needed

    160 per hour around these parts. Sounds like OP is looking for in house PC board bench work. The likelihood of any non OEM having a test bed is slim to none. Look for an used replacement board, maybe...
  10. Replies
    8
    Views
    18,183

    Re: Fanuc 21i ALARM 24 HELP !!!!

    Not to horn in on drdos, the inputs and outputs use 24volts. Some where there is a short in the wiring, that is connecting your 24volts to ground. With the power off, measure with an ohm meter, your...
  11. Replies
    1
    Views
    1,154

    Re: Doosan DVC-320 Home Reference Questions

    Non absolute machines do not store home position, they set it (during zero return at power on) based on an switch and grid shift parameter. The battery on the APC machine is not for power outage, it...
  12. Replies
    1
    Views
    1,170

    Re: Okuma And Howa Act 5 Lathe

    I would check your outputs, and wire connections. That many things that are not working have a common cause.
  13. Replies
    4
    Views
    1,317

    Re: Orient Spindle For Broaching

    Try M19 S___
  14. Re: Need Assistance Victor Lathe Fanuc series 20-TA

    The Yellow Fanuc books are your best resource, if you do not have them just find the PDF's on line.
  15. Re: ACE V400 spindle position to high for tool change

    Sounds like your stored stroke limits are off.
  16. Replies
    9,196
    Views
    334,041

    Re: The Coming Climate Change

    Well said! Now if only the climate fanatics can find a shred of common sense, before they vote in a Mega Tax to fix their boogieman problem.
  17. Re: The X axis compensation page in not visible in my turning machine with Fanuuc Con

    Pitch error will not change, it is the error correction for the grinding of the ballscrew. Any wear would show up as BackLash.
  18. Re: The X axis compensation page in not visible in my turning machine with Fanuuc Con

    What machine is it?
    Unless you have changed out an major component (ballscrew) pitch is normally not re comped.
  19. Re: How to get rid of a large amount of cnc components (balllscrews, rails, motors)?

    HGR is here in Ohio, they do large scale industrial consignment sales. Shipping would kill your deal. Somebody else must be doing something similar, I would look to the nearest area with industrial...
  20. Re: The X axis compensation page in not visible in my turning machine with Fanuuc Con

    On an 18 Pitch is normally under System hardkey, then arrow right or left multiple times until pitch is an softkey.
  21. Re: How to get rid of a large amount of cnc components (balllscrews, rails, motors)?

    Ebay would be my 1st choice. HGR #2, Craigsrisk #3. Machine tool Scrapyard #4. Where are you located?
  22. Re: The X axis compensation page in not visible in my turning machine with Fanuuc Con

    What Fanuc control? What compensation values are you needing to correct? Grind pitch error, backlash, or ?
  23. Re: ACE V400 spindle position to high for tool change

    It sounds like your axis reference, or 2nd reference is off. The manual should tell you how to reset that.
  24. Replies
    5
    Views
    1,299

    Re: problems with parameters fanuc ot from 1988

    What machine?
  25. Replies
    1
    Views
    924

    Re: Fanuc oi-mc not sending power to control

    Your I/O has a problem. Look at the X bits on the diagnose page, if all are the same you have a 24 volt problem. The machine will not turn on the drives with that condition.
  26. Thread: RT Board ?

    by ifixcnc
    Replies
    10
    Views
    1,244

    Re: RT Board ?

    Who flashed the RT board?
  27. Thread: FANUC 21 T

    by ifixcnc
    Replies
    15
    Views
    1,664

    Re: FANUC 21 T

    I think Hyundai bought KIA, try www.hyundai-wiamachine.com
  28. Thread: FANUC 21 T

    by ifixcnc
    Replies
    15
    Views
    1,664

    Re: FANUC 21 T

    The machine dealer who sold the machine when it was new, should have a back-up. If Fanuc ever worked on it, repair or add option, they will have a back-up.
  29. Thread: FANUC 21 T

    by ifixcnc
    Replies
    15
    Views
    1,664

    Re: FANUC 21 T

    If your battery was expired you may just have corrupted memory. Look in your manual for the Boot Menu, maybe you can recover with a system restore, if you have a SRAM back up.
  30. Thread: FANUC 21 T

    by ifixcnc
    Replies
    15
    Views
    1,664

    Re: FANUC 21 T

    Ebay often has these items for much less $. Also there are some aftermarket re-sellers Buy FANUC Parts for Less - New and Replacement has helped me a time or two.
Results 1 to 30 of 500
Page 1 of 17 1 2 3 4