Ygorek
Your work is superb
Regards
Kel
Type: Posts; User: nivlek
Ygorek
Your work is superb
Regards
Kel
Dear Ygorek
Please consider to put it on your site
Regards
Ygorek
Could you please advise where I could find the stl files on ?????? ???????? ???????? ??????? , for the dos shown in #121
I can see it in the wood section on your pages but cannot fine the...
Ygorek
I sent you a email for a model to be made ?
Did you receive the email.
Kel
Ygorek
As I have purchased and used your designs previously, I find them very good
But last time I used a different web site, and the payment was easier.
I am not afraid to use your Russia web...
Ygorek
Is the an English button on your WEB site ??
New models here ---> ?????? ???????? ???????? ???????
I would like to down load some more but am confused with the language
Regards
Kel
Please try this one ?
Please try the attached
Dave's not here
The way I did it, was go to the Ygorek's site (sites in Russian, I think) give a donation and pick the files you require.
Reality is, Ygorek, does these files in his free time ( I...
one of my pieces that I used Ygorek's files.
Not as good as Ygorek, but presentable..
Thank you Ygorek
Yes I understand Ygork
I have purchased a few models off you previously
Kel
Gee your doing some beautiful creations
Regards
Kel
I am an Australian living in China for the past fourteen years. I run a small business here and have fallen on some despicable business people who cannot be trusted.
I guess this happens in all...
gosh that's impressive
That looks awesome
Well done Ygorek
Kel
ygorek
That looks fantastic
Kel
Thank you Ygorek
they look great
What finish will you do, please
Kel
Ygorek
Could you please give us some machining details like
Size of the piece that you will cut
Size and make of the machine that you will use
Size of the cutters
as the detail looks very...
I am an Australian living in China for the past 13 plus years. I run a small business here and have fallen on some despicable business people who cannot be trusted.
I guess this happens in all...
I wish to say thank you, publically, to Ygorek
Great work, good detail and good service for people asking.
well done
Nivlek
Any help would be appreciated
Would anyone know if there is a post processor for the X-Carve machine ??
regards
Nivlek
I run two 60watt laser machines. Both machines also use a CW-3000 water circulator.
I have a digital temperature gauge near the laser machines and also take note of the temperature gauge on the...
Wayne
Maybe many things, but what I found on mine was a mechanical problem
Check your motor belts and pulley / wheels. Look for any metal , plastic , or rubber shavings where the pulley / wheels...
After 8 months, I’ve had a chance to get back onto this again. After, another trial and failure. (That’s three so far) I have cracked it, finally.
I still believe that BobCad, kind of, machines...
3spin
I have a 60w machine and I use 55% power with 12mm movement speed at 25 degrees and mine can easily cut 1/8" mdf or plywood.
You commented on the mirrors, Are the mirrors aligned all the...
Any further ideas, from the knowledgeable people out there ...please ?
Thank you for the couple of answers , but it's still unclear what is best for the tube
Regards
Kel
Is it better to do this
"As a general rule, when cutting use full power and adjust speed from slower to faster to find fastest cut speed"
or
use 30% power and a slower speed rate.
I ask...
Is it better to do this
"As a general rule, when cutting use full power and adjust speed from slower to faster to find fastest cut speed"
or
use 30% power and a slower speed rate.
I ask this...
Ok , thank you Dan
I guess it will be a personal choice
Kel