Hi Rasta,
yes, the controllers are still available. And so are blank PCBs.
You can contact me directly: uli at uhu-servo.de
Uli
Type: Posts; User: ulihuber
Hi Rasta,
yes, the controllers are still available. And so are blank PCBs.
You can contact me directly: uli at uhu-servo.de
Uli
Isn't the emulator designed for 3,5" floppies only?
Is there one for the old 8" system?
Uli
Hi,
I needed a way to visualize the XY2-100 output for repairing a Rofin system. As nothing was readily available, I ended up with writing a decoder for the Sigrok Pulseview logic analyzer.
This...
Hi reza,
I have a MSG-803 (used) I could offer you. I think it has the same CPU installed and boots up straight away.
there is a, original flash card plugged in with an OS/2 Mori kernel.
Uli
Hi,
I got a M&H Infrared Touch Probe 25.41 from Hexagon Metrology out of an evaluation setup. This thing has not a single scratch and is way too precious to throw it away. Sadly, I got no...
This is for sure the point. I've got the 18i-MB5 and it has the milling software. I doubt having the lathe software somewhere hidden in the system....
It's really difficult to get answers from Fanuc...
Thanks, that's what I expected.
Any idea of what this could cost?
Hi,
I've got two 18i-MB and need a controller for a lathe.
Is there anyone with an idea how to convert a 18i-MB to a 18i-TB
Thanks
Uli
Hi Vroemm,
sorry, this link is not on the UHU home page yet. Will happen next days.
Uli
Hi Beni,
since this thread diversified a bit, I do not know what parts list you are requesting.
But the newest would be the greatest anyway: http://www.uhu-servo.de/UHU_PCB_3_13.pdf
Best...
Hi,
I know this is an old thread, but I was looking for this information myself and like to share it here.
It's fot the TNC135 but should be the same:
23,24: +12V
21,22: Gnd
18,19: Video...
Ahhh... this might be the strange data in the right part of the data field. Thanks for the info .
Uli
Jon,
here it shows again, that even small projects should be well documented - which I didn't ... :-(
Just my sequence for starting a position telegram on an Attiny2313 (20MHz)with some remarks...
Bruce,
shure it is possible - who knows... ;-)
This a snipped from the telegrams from a slowly turned Pulsecoder:
UHU Pulse(de)coder 0.9 (c) Snr: 1...
Hrh,
thanks for the offer. The parts are
A230-0603-X001 u-shaped part
A230-0602-X002 flat part
A230-0603-X003 fan holder
Might you give me a rough figure what price these will have ?
...
Jon,
I started to analyze the protocol of the 1000 series pulsecoder a few years ago.
The serial protocol is carried over RS422 and can be stimulated by a simple sequence. I programmed an AVR...
Hi,
I have some SVMs (i.e. A06b-6124-H205) with broken casings.
Fanuc Germany did not even answer my request on these brittle yellow plastic parts.
Is there anyone who figured out how to get...
Hi Sinha,
after installing the amplifiers, the graphics work fine.
However, it seems not to work without them.
In the Servo Motor Parameter Manual I found a section 'Serial feedback dummy...
OK, that's what I need to do next.
For running a program, I need however to install first the amplifiers. This brings up the need for a 400V line down to my room because I can't do the testing in a...
Hi Sinha,
I dont have a MDI panel because may system is an openCNC. The MDI keys are softkeys on the Screen Display Function application.
There is a graph key and I get into the graphics screens,...
Hi Sinha,
I tried to do so, but I never see any path or workpiece in the graphics window. I admit that I am not used to these controls so maybe I just did not find the clue how to activate it....
Hi,
I am looking for a way to 'run' a 18i-MB without any amplifiers just for training.
This would bring up the need for dummy axis X,Y,Z,A and B.
Could this be possible or is it just one of my...
Hi cnc2149,
thanks for your answer. Assignment of the modules in the PMC I/O section was the key.
My fault was that I stopped on an ER97 I got each time I looked into the PMC. And I did not...
Hi,
I tried to connect a Fanuc A03B-0807-C011 AIF01A PLC I/O interface module
to my 18i-MB (JD44A to JD1B) to use digital I/O module for the power cabinet functions and I/O panel.
But the...
Hi Fanuc-users,
maybe one of you is able to give me an advice concerning a Fanuc 180i-MB I found for cheap and try to get it running.
I managed to get the CNC working in conjunction with a...
Thanks Gary,
I have Ethernet Screen Display Software. I managed to patch the SRAM-File for a valid IP-Address and I get access to the controller. But it is still limited.
I can't run the PMC...
Thanks Gary,
there is a HSSB card, but I do not have the PCI-HSSB-card for the PC side. And this looks like a pretty serious investment.
If I use HSSB with my Screen Display Function software,...
Hi,
I got a 18i-MB5 standalone CPU from a industry surplus. Along with the CPU I got disks with Focas and Screen Display Function.
As far as I could find in the manuals, it looks like the Basic...
Jay,
I'd like to anwer your posting as well as the email you sent me right here.
To make it short: I do not share code. There are several reasons for this decision and I am going to name the...
Yes and no.
Yes, the article refers to the UHU Project.
No, the UHU is not just a modified SMC. The SMC was a starting point to learn how things stick together in the transfer from theorie to...