Search:

2500 rpm feed of .001 ipr?

Hi fred..when i am touching off a drill, say T2222 on the cyclone,..does it matter whether im in absolute or incremental when i press " Z0" enter?

Gracias.

yes.. do you have a cyclone?

Does anyone have a sample barfeeder end of bar sub routine handy? Thanks...m31, m56, m81,,,m0.,, etc.

Grooved collets normally start at .500 dia and larger....what diameter barstock are you running?

Increase your bar loader pressure

can anyone provide me with G and M codes for this machine? thanks [email protected]

you might want to try a grooving insert....031 wide..use a holder from ISCAR that is used fro grooving/turning...and parting off...maybe try G96 for the angle so the chip load stays the same...

i have extensive experience drilling 304 and it work hardens.. i would drill the small hole first...peck with a tin coated cobalt drill..make sure the second drill also has the same angle as the...

use the biggest endmill you can to do the "inscribed" circle...in this case .250...leaving .0035 all around so that your .062 dia endmill only cleans up. and yes g12.1... first do front.. then...

use a pin gauge in the er collet,..touch off to the bar stock in x and in y...do the math....for example...working with .500 dia barstock,..and a .250 dia drill/shank... use a .250 pin gauge in er...

my name is frank..ive worked in many so cal shops..oranhge county, san diego county..la county, and currently in the inland empire...where are you at? [email protected]... i have more than 10 years...

Anybody ever turn this? ,im doing 2500 RPMs,...turning from .562 to .125........im going x.4+2,x.362,,x.262.....with a.0156 radius insert..

Anybody ever turn this? ,im doing 2500 RPMs,...turning from .562 to .125........im going x.4+2,x.362,,x.262.....with a.0156 radius insert..

can anybody provide me with G and M codes for a Star SR-10J,....an SR-20RII........and possibly an SV-20 and SV-32?

thank you
elsanch

drill and pin the bar stock to brass or aluminum 8 inch rods,....use all your good stock up

r u in the correct plane selection? x-z, y-z,.....G17, g18, or G19...that will make a difference

any suggestions as to what works better for Invar material. (4750) NICKEL IRON ALLOY. Im drilling a ,032 dia hole , .300 deep. is TiN coated Cobalt better than Powdered Metal drills? any feedback...

how wide should my cut-off be for parting off .125 dia barstock, but the part off side is turned down to .112 dia. i dont have a right hand cutoff (we are using a left hand), and no extended nose...

in the meantime, you can rig up a small vaccuum. when i started working where im at now, the ejector servo was out. we hooked up a vaccuum from home depot. rewired the cord to a flexible sensor...

I'll second DCogswell, I run very small holes on swiss machines, and you can nevr go wrong with Guhring drill bits. The best. Pricey but it will save you headaches. Make sure you get a coated drill...

I am going to run an 11inch long part. in my program afgter i support with the pick-off, open the main, have the headstock move back (allowing me more travel),close the main collet,...what or how do...

anybody ever replace a citizen L20 light? type7. if so, what s the part number?

anybody ever single point a 4-40 thread on sub spindle? onle like.120 length of thread on 304 ss? (.125 dia barstock?)

that machine kicks butt... so many diddferent things you can do. ever seen a thread whirlrer?

Would I have to use theis line for support?

G114.1H1D-2

whats a G811? G810?

i was told the L20 wont allow me to mill, or thread while in G650 mode beacause of my workshift W-.600 (for the face of part to come out in-line with the centers of the live tools). is that so?...

Hello Citizen gurus,
I am wondering if anyone can send me a sample program of using the sub spindle for support "WITHOUT" using a G650 pick-off code? I am trying to support for a milling operation,...

i think it might just be a matter of getting the cnc L20 ready to receive,...in other words get the machine ready so all you have to fo is hit "input"...then go to the pc and send the file...got to...