That video is on a next gen control. If you have an older Haas it won't work. Check your batteries on both tool presetter and spindle probe. Search youtube for haas automation probe troubleshooting.
Type: Posts; User: wcbob
That video is on a next gen control. If you have an older Haas it won't work. Check your batteries on both tool presetter and spindle probe. Search youtube for haas automation probe troubleshooting.
I believe if you feel you are qualified without 10 years experience, send a resume.
This position is responsible for frequent online meetings, face to face, onsite communications with customers, sales, service and other departments regarding technical machine applications...
Haas Factory Outlet
1338 S. State College Pkwy
Anaheim, CA 92806
Contact: Crystal Lewis in HR @ 714-635-7373 x223; [email protected]
Job Type: Full-Time
JOB DESCRIPTION –Field Applications...
Check your pocket tool table Have you had to recover the tool changer? If you call up tool 1 what tool does it say is in the spindle?
Is HSM enabled? How big are your moves?
Press parameters button once type 315 press down arrow key. There should be a 1 next to high speed machining
Ok its possible the amp is gone bad, but don't give up you can always talk to service at the factory and try to walk yourself through this. You might be able to move the tool arm in debug mode.
Verify the parameters in the control with the ones that came with your rotary. If you lost you parameters your local HFO should be able to get them for you.
Ken,
Doesn't he need to rotate about X & Y also
Bob
This should help you will need to be in Debug to get to the Raw data screen. You want page 9.
Good Luck
Bob
The Vm is 30 hp has a different ball screw, a different table, different casting the casting is actually the casting of a VF-5.
The VF-3 and VM-3 are Different.
The Battery is located on the processor in the back cabinet. You'll have to clip on a good battery while you solder in the replacement. Before you do this back up you params, settings, and programs...
Yes it will
goggle coolant maintance.com good info. I use the tube type skimmer from Zebra because its small and works, here in the haas showroom in anaheim.
There's the Tool room Mill
Greg it was nice to meet you as well, remember any time you need help where here for you.
EDIT: I know what you're thinking, "But Matt, you dumbass, the tool probe measures in diameter...it will put diameter numbers in the wear column!". Looks like with the use of Ix (x= nominal tool...
to set a angle use M19 with a P or R for the position.
For EX.
M19 R45.
Try Shop Floor Automations near San diego California 877-611-5825 they have a little box that will allow you to do what you want
www.shopfloorautomations. com
I use Mobil brand red grease on the tube it says Mobilith SHC 100
Bob
HFO Anaheim
try and lube the top of spindle taper very lightly and draw bar
Whats not staying calibrated the length or dia? Is the probe head moving in the holder are the jack screws tight? can you spin the probe body? How do you know it's not staying calibrated.
I called onecnc here on the west coast thats perfect.
Thanks
BTW I just started using onecnc a few months ago, I like it.
I am looking for a free software so our service techs can upload software via RS-232 anyone know of something free and easy to use?
Thanks Bob Aikins Applications HFO Anaheim
You can get the pdf from renishaw, I am assuming you guys are takling about the Inspection Plus Software. Renishaw part number H-2000-6222. Most applications engineer at your local hfo should have...
If you purchased the probe from HAAS already loaded are the macros for some routines call Renishaw ask for the manual H-2000-6222-00-B or whatever is newer if the have one. They should email a pdf.
...
Ingersoll makes a spring loaded er 32 collet holder and adapters
Variable for the serial number is #6026
Good Luck
Bob Aikins
Haas Apps Haas Factory Outlet Anaheim