502,923 active members
7,056 visitors online
Register for free
Login

Search:

Type: Posts; User: datac

Page 1 of 14 1 2 3 4

Search: Search took 0.01 seconds; generated 34 minute(s) ago.

  1. Replies
    0
    Views
    26

    Re: Newbie to Flashcut CNC - Error Code 1322

    Does the machine have homing switches at one end of each axis ? Did you home the machine to those switches before you jogged ?

    When you home the machine and it locates those switches, the MACHINE...
  2. Re: Vcarve is it possible to copy with tool path?

    Ok, I missed that you need to cut numerous qty's of the same word.

    Well, there is always the ability to do copies using potential codes in your control directly. Most controls will allow you to...
  3. Re: Vcarve is it possible to copy with tool path?

    With VCarve, you could create a job with all sorts of words that start with A, another with B, and so on. If someone wants a word that starts with R, you open the R drawing.

    If someone wants a...
  4. Replies
    3
    Views
    565

    Re: CNC Motion Control Board

    It shouldn't be, at least if it is MINT. It practically looks like and works like XP.. Same old start button in the bottom left, a popup menu of your programs, simple and easy software installation...
  5. Replies
    3
    Views
    565

    Re: CNC Motion Control Board

    BUT, you can be slowed down by other things that sadly, are only addressed deep in documentation that certainly should be in Step Config..... DEBOUNCE settings for limit switches or other touchy...
  6. Replies
    24
    Views
    1,137

    Re: CADs for free comparison

    Remember these words.... Whatever "FREE" cad offering your seeing or currently using that are offered by non-open source companies will very much so become NOT FREE, right about when you get really...
  7. Re: Small Composite Router Build 1000 X 600 X 300

    Gosh, I am just confused a little when it comes to building these small footprint machines out of anything but real metal. What exactly is the advantage ? Light weight ? Portability ? One could make...
  8. Replies
    2
    Views
    421

    Re: flashcut to control a relay

    I'm not exactly sure whether they intended those two connectors to be used with a traditional 3-5 volt (or higher) Solid State relay directly or not... I think I recall those two being an actual...
  9. Replies
    19
    Views
    1,929

    Re: sensing program zero

    Below is what I use for center finding... note that I have one on the machine that runs this twice in a row for holes. Doing it twice gave me more assurance and accuracy. Also note, you need to...
  10. Replies
    19
    Views
    1,929

    Re: sensing program zero

    I have made similar routines over the years and use them with Flashcut........ I'd have to look at them to see what methods I used, but I would assume they would look similar to the OP's.
  11. Re: Vacuum Pump, Who uses them and What do you use?

    I've used closed environment vacuum for work holding on and off for years. A closed environment is one where you can control your leakage, which is different than the systems that use a high...
  12. Re: Windows vs Linux Mint - Possible Strategic Advantage ?

    >>> Did you know it was written by a bunch of Russians, in Russia, and that AutocCad bought it. Why, I don't know, as they try very hard to ignore it.

    Somewhere I had read they "acquired it".... I...
  13. Re: Windows vs Linux Mint - Possible Strategic Advantage ?

    I can't speak for version 10, but my Autosketch version 9 runs under Wine. The only things I have noticed are at start up and shut down, and neither is serious.

    When I start up, I always get the...
  14. Replies
    3
    Views
    596

    Re: Diamond Drag simulation barely shows up.

    Are you setting any depth in the tool path ? Usually, when using a spring loaded spindle, one would not set any depth, and allow the depth or pressure to be put down based on your Z zero location.
    ...
  15. Re: Would you run vacuum collection in my case?

    If you do not have the space for a largish, properly plumbed exterior dust collector, consider a traditional home central vac unit. For your size machine/operation, it sounds like a fit.

    Unlike...
  16. Replies
    372
    Views
    18,891

    Re: Chris' G0704 build

    .......with a sliding polycarbonate door and coroplast back and side walls.

    Ya... that is where I am headed too. Well, not completely with 80/20 though. I am thinking of just using "aluminum...
  17. Replies
    2
    Views
    238

    Re: Denford hardware choice

    I think the only reason that could exist is simply if one had to get it running with the least amount of money. Any time savings doing it thru the existing drivers is going to come from the fact that...
  18. Re: Looking for CNC Lathe With Manual Capabilities

    Pretty sure ProtoTrak is another. In fact, I believe you can grab a hand wheel even with the machine running to back off from a cut or approach to a cut and the controller will re-correct from any...
  19. Replies
    57
    Views
    42

    Re: Arduino GRBL VS LinuxCNC

    >> In any event in my simple mind your CAM solution should not be your GCode sending solution.

    I agree with this statement to a point, especially in that at least the main or home portion of the...
  20. Re: GrblGru: Free CAM and 3D-Simulation for mills and lathes

    I have to say, the amount of programming and the type and functionality of programming you are doing in this program is nothing short of amazing. I do not know of any control program that has visual...
  21. Replies
    57
    Views
    42

    Re: Arduino GRBL VS LinuxCNC

    I'm not one of those guys, but I have seen and attempted to use the program. While it clearly is admirable that the developer just keeps pounding away at adding interesting features, I can not find...
  22. Replies
    6
    Views
    594

    Re: Small Lathe Suggestions for CNC Retrofit

    My understanding is that there are more Denford Orac's to be found in the UK than in the States. So if I lived in the UK, I'd set my sites on finding one. It is similar to the Enco 8, but feels more...
  23. Replies
    2
    Views
    9

    Re: Need Controller For LC4896

    Based on the way you worded your issue, it would appear that you are not familiar with retrofitting in general. There are many, many potential controls that you can fit to that machine, but, a...
  24. Re: List of CAD Software Companies that are NOT subscription/cloud-only (or have plan

    Nailed it. Seems the most annoying and painful to the wallet was when the CAD side dragged miserably behind the awesome functionality other programs were offering... But there you sat... paying for...
  25. Re: List of CAD Software Companies that are NOT subscription/cloud-only (or have plan

    Lately, all I hear is how great and wondrous Fusion 360 is, but I find myself counting the days as to when that "Free" plug is pulled on the hobby user. Perhaps all those so hyped about it are too...
Results 1 to 25 of 348
Page 1 of 14 1 2 3 4