Would anyone have a wiring diagram or even a picture of the wiring inside the spindle control box on the front of the head of a series II
CNC mill?
I need to rewire the e-stop-forward reverse and...
Type: Posts; User: cncbpt
Would anyone have a wiring diagram or even a picture of the wiring inside the spindle control box on the front of the head of a series II
CNC mill?
I need to rewire the e-stop-forward reverse and...
I am selling a new-never used Kurt Vise
Check it out
THANKS
Kurt HDLM6AL 6 inch Wide High Density Double Station Manual Vise Base CNC | eBay
I have it
just need an email and I will send it
I used a Hillbilly BOB on my series 2
Its easy to hook up,uses original steppers and Mach3.
Doesn't get any easier or cheaper and it works great
Thanks FORHIRE
I read the programming manual a couple times regarding the use of G2-G3 and got it to run perfect
pretty much just like you are saying
Takes a few minutes to cut the 0-ring...
I was hoping someone here could help me with a programming problem on a TC22 with a dx32 control
I have 62 parts to setup and drill a bolt pattern which is no problem but I need to cut an o-ring...
Old post but I am not on here much
I have the software if you still need it
What do you need to program?
I May be able to help you out
I run a sl10 with a cent 7
Also familiar with the VMC,s with this control
milltronics has one of the best controls in my opinion
I have full copies of the dx32 software for a TC-22 if you need it
I have had this same problem over the years
I will have to do some remembering as its been awhile
I went through about every...
I have a 97 if I can help with a picture or two just let me know.
George has help me several times and I would be glad to return the favor to someone
I have a TC-22 that has done alot of work for me.
They are pretty nice little machines all and all.
They all seem to have about the same issues that will come up along the way.
Thanks to George...
Here is a unit I make and sell if anyone would be interested
Spindle Pulse Index for use with Mach3 Cnc Lathe Mill Retrofit | eBay
It is easy to setup in Mach3
I am using one on my retrofit
I am working on a Emcoturn CNC lathe conversion from the original control over to Mach3 and servos with Gecko drives.
I would like some advice on what would be the best wire and gauge to run from...
Can someone please shed some light on my problem
Getting modbus working with a hitachi x200 ?
I have read for days on this and i believe i have it set up correctly
But i get timeout errors once i...
Possible your CMOS battery is dead and lost all your CMOS settings
Now it doesnt know your hard drive parameters.
hopefully your hard drive is still fine and you can just replace the battery on...
I just started a retrofit on an EMCOTURN 140 lathe.
I sold the original control in favor of running this lathe from Mach3
I am going with a VFD/3 phase motor for the spindle,850 oz/in servos with...
I have a SII and if you dont want this one I will take it if close enough to Ohio.
You dont want to pass it up.
Guys go out and buy the BP clone machines for far too much money when there is these...
If not awarded please send a dxf or dwg file to [email protected]
TOP PERFORMANCE RACING
Thanks
The machine in the video is my lathe.
All original but I dont have the tailstock.
I paid $1800 for mine.
If you can wait till tomorrow night i will fire up my TC22 and get you these parameters
That is the version on my mill now.
I believe that to be the newest version of software for this machine....
Sorry what I had didnt work for you.
I had the problems with the a drive working half the time too.
I ended up finding on EBAY N.O.S 486-66 motherboards,new powersupply,
Floppy ,I/O card and...
I sent you files again like last time
I canot get yahoo to send them
These are the same as on my mill right now
Hope these work good
Good Luck
I wish I would of kept a Log of HOW TO for this
I was looking at your pics and I dont see any ribbon cable coming from your BMDC board.
Also the crazypic picture is the same thing I got after loading my new software.
I believe you should get the...
I have dos 6.22 if you need that also I have the software for a torq-cut 22
if that will work for your machine.
Since you have your original bmdcprm.sys file it may ,George or someone will have to...
I am in Ohio also.
I am going to let my mill run at about 350 rpms for half an hour or so and see if it still does it.
I have been watching this thread to see how you were making out.
My machine will shift from high to low no problem but shifting low to high
it will error out.
When I reset the control I find it...
Was there ever a conversational package or a cam program that was available as an add-on for a dx-32 control?
I need a way to make programs at the machine like would be possible in a conversational...
I was told to use Marvel Mystery oil in the air mist unit for the shot pin to help it operate smoothly.
May be worth a try for you.
Somewhere in my files I have a service bulletin That...
It is what was recommended for my TC22 so I stayed with that.
I have read that the formulation has changed since it was used years ago
but I have stayed with it and have not had any problems.
I...
I am using Mobile Vact 2 also and get it from MSC