Thanks but I do not have mach 3. is there no one at all who will help me along the way?
Type: Posts; User: Gunni
Thanks but I do not have mach 3. is there no one at all who will help me along the way?
No it’s all gone.
I have a CNCRouterparts PRO 4"x8" from 2014. It has been unused for a few years, and when I wanted to start using it again my PC was broken so I do not have the original MACH3 settings.
I then...
Thanks for the help, I started to design an after a few days, and as I said I'm not so good at it but I felt it became very fine. Funny enough it´s very similar to the one you drew :)
I have cut...
Christmas is approaching, I do not know how it is in the US but in Denmark many children believe that an elf moves into the loft in December and if they do not behave properly the elf teases them :)...
Hej Puk
Velkommen til, jeg tror ikke vi er mange danskere :)
Jeg er selv nybegynder og har importeret og bygget en CNCRP maskine PRO4896 4' x 8' CNC Router Kit | CNCRouterParts det er begrænset...
I have a 2.2 kw water-cooled spindle, I've created a reservoir of aluminum that can accommodate 0.75L water, will it by itself be enough to cool the spindle or should I install a radiator too?
...
Sorry for my late reply, on the same day Cory emailed me a solution.
I am putting his answer here as he explains it well.
Cory Kocher wrote:
I believe the issue is the setscrews are pushing...
Thanks for your reply unfortunately, the V-Con Clamps have some pins so they self center even without the screws are tightened. so it's not going to help.
I am well started with my PRO 4896 kit. But I have encountered a problem when I was to install the Gantry R&P Carriage Assembly, the gap between the two steel rails are too big so the Gantry Carriage...
The Wooden Letters Company
its the workbench it's going to sit on not all of it just the length of the x-axis so I have something level to put the aluminum extrution on it's been done on a lot of builds but there have always...
Can I use the polyester resin to level my x-axis (the table where my PRO4896 shall be on) instead of the epoxy?
Casting polyester seems to have a very low viscosity and is self leveling and it is...
Thank ger21
Know some good suppliers? I'm sitting right now and looking at toolstoday they seem to have a large selection. it's hard to find your way around as a beginner, suggestions would be...
Thanks for responding both
I have a 2.2 kw water cooled spindle from china like so many other uses. and 1090 oz-in Nema 34 motors. I'm not sure what other information you need, as I am fairly new to...
Hello everyone .
Now I'm almost ready to build my PRO 4896 all the parts from cncrouterpart has come I have my aluminum, spindle, motors etc. so it is only small parts that are missing, of course...
No one will comment on these stepper motor Specs?
Hello everyone
I'm from Denmark and is going to build a cncrp Pro 4' x 8' machine (my first CNC)
I 've talked with Ahren and Cory from CNCrouterparts they have been very helpful, I would like to...
I have seen the videos cncrouterparts have made and they are also good. I was hoping there might be some other videos that I had not seen. I like to see people's videos I think it gives a good...
Hello every one
is it just me or is there not really any videos of cncrouterparts new pro machines with V-con system?
There are lots of videos of their old system but very few of their new.
I...
Hello really nice build.
Whad size steel are you using for the frame and the gantry?
Sent from my iPad using Tapatalk HD
hi i am new to CNC and going to build my first machine, I work a lot with RC Cars and Planes and would like to make some parts for this, as well as all sorts of other Hobby projects ;)
I want to...