Just to update I replaced the servo dist board and every thing is up and running.
Type: Posts; User: turboboy
Just to update I replaced the servo dist board and every thing is up and running.
Thanks for the reply.
I talked to haas and he told me that power dist board also. I told him my dc buss was zero and he was sure the board was toast. Just waiting on a new one and i'll post if it...
My 1995 vf-0 is giving off low voltage alarm .
Does anyone know what board the machine reads the low voltage alarms from or were to look?.
All my boards seem to have the proper voltage going...
Can any one link me to any suppliers for tumbler media in canada?
Found lots in USA but shipping costs are killer.
When you spend thousands for a machine you at least expect to get what you pay for.
12,000.00 is a good chunk of change to have sitting in corner of a building not doing anything.
I expect...
I would stay away from dyna cnc they never stood behind any of the problems I have with my machine. Sure some have had luck but theres lots that have not. I have lot of PM'S from people that have...
You can also post or pm me your email and I will email you .
As I mentioned before I did cut with the dyna table for less than half hour. The small time I cut on it I had to support the material with blocks and anchor it to the table with straps .Reason being...
The sales person (juris) told me to contact tech support with my problems. When a decision was made ,steve or heather said it was discussed with dave ( im guessing thats you?). I have the emails...
Toby the total length will be around 8" width is 1.5" height is 1". I have 2 kurt vises and also selection of alum jaws i have been using.Its 6061 alum.
thanks
Im new to machining. I have a haas VMC and want to machine a part like the one in the picture. Whats the easist way to hold it. I was thinking machining the bolt holes for the caps. Then the bolt...
I purchased a 4 x 8 table from dyna cnc in washington. It has been sitting for 5 months . When I got the table they sent wrong parts, mounted the table wrong postion... list goes on. Basically they...
Question:
How do you use the chamfer function to put a chamfer on diffrent depths.
I have three circles to chamfer and the top one is a "0" next one is little smaller and -.25 than the first...
I just got this 95 vf0 , How do I go about checking the oil level oil in spindle?. What oil does it take.
thanks
Red earth what brand table?
I purchased a table from dyna cnc. I have had a lot of problems with it.
-I ordered the table with the hand torch holder for my hypertherm 1000. When i got it out of the crate they mounted the...
Just wondering if theres any others that have bought a machine from them?. What were your thoughts on it?
thanks
were do i look for antidive?
thanks
I seem to be getting best cuts with 135 on the 3/16" steel.
Is there any tips on plasma cutting holes so there nice and clean. My 1" holes i been cutting dont seem to round or clean. I tried to...
I was just cutting with it some more and on the straight cuts it seems to stay within 2 numbers of what it set it at. Must be the corners as you say cause it to jump more. Thanks for your help
Torchhead higher the number is the cut gap more or less than a lower THC number?
If i set the THC at 140 for example and you say it should stay within 3#'s. What would cause the THC numbers to...
Im running a hypertherm 1000 with ahnd torch on my cnc table with THC. Whats the correct tip to use on the hand torch?. They have sheilded or unsheilded they run? Thanks
My license wasnt installed :rolleyes: works now. thanks for the help
Thanks I should look to see my licence is installed correct.
I load a part in to sheet cam create the g code but dont get the whole part to cut.
Example: I do the words "dyna" when I put it in mach 3 theres only the
"yn"
Im new to all this , is there...
Is there a easy way to figure out the radius on a part. I need to figure out the radius to transfer in to CAD program to cut the part.I dont have radius guages but wondered if theres a simple...
I doubled check those variables there all the same tool. It seems to be only tool #3 and # 8 the program isnt doing the g code t8 in the program for some reason . Very strange.
thanks for the help
Im just learning all this g code stuff. what dialog box is H that your refering to on onecnc?
thanks
I been downloading programs from my one cnc in to haas vf0. Now I get the alarm "H and T Not Mat". Is there a setting in one cnc thats not writing the program right. Any fixes?. thanks in advance
On the THC box the torch volts. What effect does this have on cuts ect..I just got this plasma table so trying to figure it out. They dont come with much of instructions :confused:
Also what would...