Search:

Hi guys been having some long term issues with the y axis on this machine coming up with y axis cross position error A,tried all the usual things like drive tuning,cleaned brushes,checked all...

Hi mate thanks for that,it appears I have the drawing that your looking at I can see that measurement for the knock-out rod I probably haven't made it clear the measurement or torque that is needed...

Thanks heaps mav the serial on the machine is serial 7042-aoa-97-1502 control dia 91203095 6000rpm spindel a2100 control cheers.

[QUOTE=greg b;2440190]Hi all has any body got the information on removing the tool change ejector shaft from the spindel housing we have got the tools to do the job but our manuals don't cover this...

Hi all has any body got the information on removing the tool change ejector shaft from the spindel housing we have got the tools to do the job but our manuals don't cover this part they only have the...

Ok thanks guys for your imput I will let you know how we go.

Hi gus thanks for your reply been some time since we spoke,this is a old problem being rehashed im sorry but the bridgeport finally got to the stage where it was unusable.I finally got round to...

That was going to be my next thing to do i was going to swap the axis boards from x to y im assuming that's what you were referring to cheers greg.

Yea had a bit more of a look around the y axis drive board and really couldn't see a signal pot,the others as mentioned above I tried turning seperatly in different increments still to no avail and...

Thanks DJ for your reply no mine is different from the attachments you have they have a tach pot,current limit pot,and a offset pot which are all pretty close to each other.I believe there may be a...

Hi all I have a interact 1 mkll with a 2500 heidenhain control,there has been a issue with the y axis motor for some time now with rapid movements in and out with the control going into error,but I...

Not sure if this helps Ade but i had a simular problem many years ago with my interact and im pretty sure for memory on that ktk board there is a multi tap transformer that has a lot to do with...

Im not 100% sure on this but i have 2 machines with the same control one of them the mouse bounces all over the place and randomly clicks on what ever when the mouse is conected,i have traced it back...

Tom i have the same machine and had some weird issues over the years but not this one.Do you get a chance to home the machine or does this happen when just pushing the green button to activa the e...

Mike it hasnt come up with those errors but it has come up with could not align in a specified time and it will sit there and do nothing and time out.It did align this morning after several starts...

Sorry to crash this post but im having a very simular problem on my arrow 500 Mike I have suspected the battery in the drive has been causing weird problems for the last few start ups,you actually...

Thanks again mav for your reply,the hard drive in question was purchased by the original owner new from Siemens but was never configured as the original hard drive that came with the machine was...

Hi mav actually when we changed the hard drive it was one that came spare with the machine and we got it autherised by siemens and we used the floppy that came with our machine to load it along with...

Mike is rigid tapping acually in the option colums or does it come under a different heading,I found the original hard drive sheet with the authorized code I think, but im not sure this will be...

Mike had a good look this morning the hard drive we had originally had to be changed because it was damaged but it is a Siemens hard drive not a clone the new one we installed is also a genuine...

Mike we did change out the hard drive and i do have the purchased options sheet but the weird thing is the sheet does not have that as a option however when you go into purchased options on the...

Hi guys my arrow 500 was equipped with rigid tapping i have'nt used the machine for a while and went to do some drilling and tapping and an alarm saying no rigid tapping avail must purchase from...

I can well imagine the problems you encounter working on these things,I dont envy your job but I must say without help from techs like you guys there would be a lot of people on this forum that would...

Thanks for your imformation and all your help its always a pain when error codes can mean so many things and if you dont work on these controls all day long it can be like looking for a needle in a...

Hey Mav had a good look today what the voltage was coming out of the power supply PSU2 it is showing around 23.75 DC volts,I followed a couple of the wires down to the input board and the voltage is...

I had a quick look on the out put board but ran out of time to do much more,where would the most reliable place to check this voltage be.thanks for the reply.

Hi guys got this error come up on my cincinatti hawke 150 (output/fuse failure in APC Rack 0) never had this one before checked a few things out but nothing really stands out.
1 checked power coming...

Good news after further investigation,i checked relays,prox switches,etc and descided to have a close look at the drive panel that sits on top of the turret motor,which I thought may have something...

Yes the error was cleared,and the tool cannot be re zero as the turret cannot be re aligned to do anything,today I checked quite a few more things I will list them
Manualy applied air to the shot...

Hi Guys have some probs with my 150 hawke duplimatic turrel,had a very small crash that I was able to stop very quickly the turret was not tool changing at the the time the tool just overrun into the...