On a VH 65 rotary, what is the bolt hole pattern drilled in the faceplate?
I don't see it in any of the documentation.
Type: Posts; User: Welder2022
On a VH 65 rotary, what is the bolt hole pattern drilled in the faceplate?
I don't see it in any of the documentation.
It is normal practice to use a box fitting chucked in a lathe to hold taper threaded parts which have a pin on them.
Has anyone tried to thread the actual chuck soft jaws to hold a pin directly?
I...
That's way too small.
I need a new O ring for my drawbar piston on a VMC-15. Got a new one from itscnc but it's wrong; it's too slim.
Mine is 1/8" nominal; .139 actual cross section.
The one from itscnc is like 1/16"...
I set the parameters for I/O on RS232 on channel 1 and the machine will transmit a file ok. But when I try to receive
(F Input) the control flashes "compare" until the transmit from the pc ends,...
Regular 16 tool umbrella.
Help! I have an EMC with 5 hp. motor and Yaskawa 515/G5 spindle drive. Bought used, not under power.
Believed to be the original drive, but cannot verify. Rigid tap with 1000 line encoder.
The...
I have acquired a Yuasa spdx cnc rotary with no controller. Can anyone help with integrating this onto a DC Fadal currently running a VH-5C?
I have considered simply replacing the Yuasa motor with...
I have acquired a Yuasa spdx cnc rotary with no controller. Can anyone help with integrating this onto a DC Fadal currently running a VH-5C?
I have considered simply replacing the Yuasa motor with...
https://www.cnczone.com/forums/attachment.php?attachmentid=491770&stc=1Machine is a '98 HL2. Condition in the moment is it won't boot up at all. Problem started after sitting about a week. Got "low...
Is it possible to use G81/G83 can cycles on 0T? We cannot seem to figure this out. Machine is a Hardinge Conquest lathe. Parameter change?
On a 0T control, how can the letter "E" be input from the keypad? Secret key sequence? We can upload/download and edit on a pc, but cannot use the machine keypad to do this.
I am using a Fadal in format 2 with a VH5C rotary in X axis. Using Mastercam X5. I have several different posts, but cannot get any of them to output the rotary code to do a simple 4th axis job....
No it doesn't have a limit switch; just end of stroke on the hydraulic cylinder in or out. Went into diagnostics and saw that the hyd. solenoid valve was getting the signal to do exactly what it was...
Solved by new MOCON board
1998 HL-2 sat broke down for a few months with axis control problem. Tailstock was working ok. Now, new MOCON board and axes work ok but tailstock problem.
When you try to home tailstock, it goes...
I have an older Eldorado M7419 all hydraulic gun drill. I am in need of any documentation applicable to this machine please.
Just replaced the axis drive for the turret, "A" axis. Now the spindle acts like it's in "orient" mode all the time. This starts soon as you do power-up/restart and stays on till power down. Spindle...
On a Fanuc OT, how can I set it up to use a one-line G76 cycle? Right now it has to use a two-line G76 cycle.
Sorry if this has been gone over before, but search results in this forum for G76 or OT...
Metal Trades Machine llc. is looking for your business. We offer precision CNC mill and lathe work and welding including stainless and aluminum and welcome your prototype or production parts. General...
On the upper left of the control there is a "video" switch for the monitor. Is it on?
Also you have to hold down the green start button for 3-4 seconds for the control to power on.
For my Hardinge Conquest 42 w/live tooling, the manuals and existing programs in the control (OT-C) use the format " G4 T0101" for all tool changes. The purpose of the G4 is not explained anywhere. I...
Ok got it going. Turns out "hardware handshake" is ok for control-pc, but "no handshake" works both ways.
Settings are:
2400 baud
even parity
7 data bits
2 stop bits
hardware handshake
Xon=no
I have a Hardinge lathe with a 0T-B control. Using Cadem dnc software on a pc with a USB-25 pin serial converter cable to a null modem adapter inline. I can download programs to the PC just fine and...
Thanks I need a schematic drawing with list of part numbers for the subspindle drive
Thanks but mine is not a T42
I have a 1990 Conquest 42 with fanuc 0t control and live tooling and subspindle. It is missing the actuator and drive pulley and drawbar for the subspindle. Has motor and belt. I am guessing that it...
Check the wiring to the keylock switch. It may have been disconnected at some time...
#1. Quit using format 1. Use format 2. That way programs you make can be used in other Fanuc compatible controls and vice versa.
#2. Touch off all tools to the table. If you use a block be...