Search:

I got wrong tool in the machine vs turret, turret got tool two in position, but the Fagor control shows T1. Anyone know the parameter that needs to be changed to correct to get turret and control to...

I have the same issue! Battery went dead. Did you get it back up and running and how?

Thanks in advance.

Thanks Factory Guy!

I guess I will have to invstigate the problem with the write protection.

Have you or any one else who had to restore a backup into a Fagor 8050 / 8055T?
The backup is from...

On one of the lathes with a Fagor 8050T / 8055T, the backup battery when dead.
I got backup of the following files that I guess is the files needed to get it back up running again:
PLC_ERR.PIT,...

I had a problem with the tool change on one of my routers. Suddenly it did not change tool in some of my programs, but not all. It was a cable for the tool changer position that was broken. When the...

I have the same problem with my Roctech router:

Motion 8 AAxis Loss Pulse

I belive there is something wrong with the the Y-axis motors. I don´t even know if the A-axis is working properly. ...

Hello Mike,
Great to see that you an aluminium table on your mill. Wish I had one too, except the two times I sent a mill right thru the table. :)
I always use the spoil board since I mill very...

Hello MikeDK,

Great reference guide. One question: If you put a spoil board on the table, will all tools follow the new zero(if you use bottom as zero) or how do you do it?
Or you use external...

Hi,

A couple of ways to do it. SyntecLee got one that you can watch on Youtube(great way but not how I do it). I use another and Mike DK uses another one. I got a Syntec6MB and i use the tool tip...

gfacer2!

The parameter 883 did the job! Just added some mm and now it works!!!
Thanks!

Hello,

Just found out the following:
Press maintainance/ Sys. Setting / Set MMI conf.
There on the second/third page there is a parameter for the length of the filename.
I changed from 150 to...

Gfacer2,

I will check parameter 881.

The long time from cycle start to any action at all, will also happen when running MDI. The post is ok since I'm using it on the other machine.

The small...

Now I just bought another CNC router and of course there is some issues with it.
It´s equipped with Syntec 6MD.

1. The G53 zero is too close to the zero return switch. What parameter could it be...

Hello Mike,

I got both 6MA and 6MB and auto square is nothing I ever heard off.

Anyone know how to get rid of the "Z70 ABS. Illegal 0001 1” My battery died and I lost all absolute positions. I figured out how to set X,Y and Z but still I got the "Z70 ABS. Illegal 0001 1”. My...

gfacer the second, if you get any result please publish! My circles suck to!

Somewhere in the Syntec menus you can actually look at this .lad files as a ladder diagram. Can´t remember where, but it is there. If it´s possible to edit I can´t remember.

How did you get anything useful out of the .lad files. I just get crappy greek letters.

Quite funny since I´m looking for the same solution. I´ve tested a bunch of M codes and had no success activating the F buttons. I learned the hard way that M50 releases the tool from the spindle…...

I just remembered it as AUX but I think it is actually External shift. I use the tool tip routine and then I don´t put any numbers in anywhere. Sorry.

Correct.
Use like 10mm spoil board and set 9mm in aux and use program that cuts at Z0. It works great.
And if the spoil board becomes 8.5 or 9.2 doesn’t matter as long as the Z0 is on the surface...

My advice is that 3411 should only be set once. There is no need to change it if you use AUX and/or tool tip measuring.
All tools will follow the AUX value. In my case my 3411 is the height diff...

One of my router, the one with Syntec, complains if it don´t have any air and the other one has a solenoid switch that turns the air on when powered up.
I got a new solenoid laying aroung for the...

Djcregan,

What happened? Did you get it to work or still trying?

BR

Daniel

Hello again.
Run MDI mode, and a tool (like T2) with tool sensing activated and make sure that the machine will touch of the tool sensor.
Now you got a value for the tool T2 = 123.456(from tool...

I have a different way of setting my tools and tool sensor compared to SyntecLee.
In 3411 I got the height difference between the tool sensor and the table.
Run MDI with tool sensor, then MPG the...

Often you get this message if:
G54 Z is set correct against workpiece or top of material?
All tools are measured correctly in Z height?
Watch SyntecLee´s vids.
BR
Daniel

Hey,

First make sure you got G43 H(toolnumber) in the code for tool compenastion height. And the tool is correct in Z-height against workpeice or table.

BR

Daniel

Correct, and the password is 520

Hey,

Some parameters are relatively easy to find.
Do the toolchange in MDI mode, and when the spindle is in the wrong x position, hold the movement, now you have a machine position in the screen...