Hi! bobmagnuson,
I have a CRP4896 from cncRouterParts since 2012 ..... I'm tired 24 bearings for the Y axis .... I read your post, do you remember where you buy your stocks?
I contact last week...
Type: Posts; User: Dan73
Hi! bobmagnuson,
I have a CRP4896 from cncRouterParts since 2012 ..... I'm tired 24 bearings for the Y axis .... I read your post, do you remember where you buy your stocks?
I contact last week...
Thanks Andrew,
I try this software since 3 weeks, but when I choose rotary, for a STL file 3X3X24' inchs , the software need a Height of 4.27 inchs and I don't know why.
The 2 oposits corner...
Someone know if a software support 4th axis (rotary) who calculate the toolpath with a square part not a round (cylinder) so not staring with a rounding pieces and toolpath
Please help,
I have exactly the same settings of the image above
in reference of this post http://www.cnczone.com/forums/deskcnc-controller-board/242904-cnc.html
the only exceptions I have...
Hi!
I have the same settings of you, except for the KL, I have the C10 breakout board
I connect to the 14 and 16 output on the port#2 and I entered these settings into mach3 motor outputs, but to...
Hi Gerry
Thanks for the answer
this is the answer I expected
"and you can use two breakout boards with the smoothstepper"
:)
hey Dan!
2 questions :)
1) do you have a diagram of you system, because I have the g540 + smoothstepper + 4 nema23 on it with a 48VDC 600watts too, but I want to add a 4th (5th) axis with the...
Thanks Jerry,
does a single laptop with 2 USB cable (can control 2 different breakout boards) and mach3 can control the both cards ?
The second BOB is for the 4th axis in my case
or if someone...
Hi guys!
I have a crp4896 cnc since 2.5 years,
this machine run with g540 (x,y,z,x-slave) with a USB smoothstepper
and a 47V powersupply
How can I connect a 4th axis ? with the second port...
Thanks guys
anyone tried these cables track chain from china ?
Cable drag chain wire carrier 15*50mm R38 1000mm (40") | eBay
For the cost, how are they ?
HI!
This is a funny problem :)
I test the run from here with 2 files
file a) 600 000 lines
file b) 225 000 lines
with the file (a) I hit the "run from here" at line 450 000 it takes 5...
Thanks ger21
But turning off toolpath display take the same time 7-8 sec. and the timeout popup again
But for those who have the same problem
I just received a email from warp9 ...
Hi Dany,
...
HI!
I have a gcode file with 500 000 lines in Mach3
I want to restart at line 419 000 in Mach3 "run from here" but the SS watchdog timeout popup message tell me about the timeout when mach3 is at...
Hi doorknob
yes I was talking about the "pull-up" resistor
How can I know more about the "pull-up" resistor for my g540 gecko drive, I don't know exactly what kind I need to do this ...
Thank...
nobody can help me ? :(
After reading on the subject I do not understand why some uses resistance ...
Does anyone can help me with the connection of the autozero tool please ... and do i need resistor or not .. and why...
Thanks for the answer ger21
for the same price I finally found a store for all "Quebecers"
this is GBS . ca
:)
HI !
I'M Dan from Quebec, QC. :)
I started building a CNC Solsylva 25X25 and all my parts are ordered
I ordered Monday at McMaster-Carr 4 ACME rod but yesterday they told me they did not send me...