Lost all my parameters for this machine. The machine was purchased used and came with the wrong parameter Documents.
Has A Fanuc MSC 518 Control.
Any Help???
Type: Posts; User: kabdelwahid
Lost all my parameters for this machine. The machine was purchased used and came with the wrong parameter Documents.
Has A Fanuc MSC 518 Control.
Any Help???
did you ever find the answer for this question????
I have a question to everyone who knows about this control. (Meldas 500)
I had a problem with parameter and had to Initialize the control.
As I also have problem with the rs232 port i can not...
that would be really great
Did you find the Parameter I am looking for the same parameter
Hi All
Anyone ever used SIN805PC software. I searched all over the internet could not find it nor can i find anyone who has it. Any help is appreciated.
Natedog. I hope it works out fine for you. Its not so hard to do. And you ll allways be able to pull the board back out and redo it. As long as you have the grafic card and the keyboard. Make sure to...
i did nt get what I should tell u?
the Bios configuration depends on the board version and bios version you have. In my case it was only to get the bios back to default configuration .
and just...
ok first of all i would try to disassemble clean and reassemble all boards ones again.
make sure all boards are in right place and all connections are clean. you say you replaced battery for real...
can you describe your problem please
do you have the parameter as backup now or could you chare the information of the person who helped you out. I still need parameters for a 600e /e2 analoge spindledrive with toolchanger. I tried a...
did it start before battery change
I also need the files for the maho 600 if posible
kabdelwahid at gmail.com
Dear All
After a initialize procedure on a Meldas 500 I m somehow not able to get parameters back up on the cnc. I configured I/O Parameters back to what they originally where and also am able now...
I started working on the machine from the point the monitor did nt even turn on. with a lot of problems starting from memory loss till many boards had to be cleaned. had problem with door closed...
wiring diagram does anyone has the wiring diagram as well
Superman I did already. two problems left spindle not working and I have an 8 staion duplamatic .. in your file I just found 4 duplamatic...
does anyone have the full parameter files backed up. I would be thankfull if anyone could e mail them to me.
thank you all
OK Many posts on this forum discuss the problem of when the system looses software or better said the battery failure problem.
for most people it will be easy to get this control back to life by...
do you have the system software to reload it back on your machine
u don t need a disk. most common steps to have a working realtime board are.
Exchange batteries.
get an old isa vga board a really old keyboard and a normal monitor and a powersupply....
Make sure all Your connections and cards are placed correctly and are firm. Reattach each connector to be sure.
nothing to worry about Pasan
check steps described from akram second post on this thread. this will do the trick. did you ever disassemble the controller. the real time board is the one at the far...
Ok on an ultimax 3 I get an alarm when starting the machine that all axis have errors xyz and s.checking the cabinet all axis have a .- and s has a 0 what i believe is ready to go. so i believe it s...
figured it out. problem was in the dip switches on the personality board.
figured it out. problem was in the dip switches on the personality board
Regina here mentioned the blinking cursor and the dip switches on the Hurco personality board. then you said you fixed it but never how it got fixed. I am facing exactly the same problem and hoped...
ok when pulling out the personality board it boots up slowly as said. reinserting it brings me back the blinking cursor
I have a friend with a really old hurco with the Dallas chips. I figured out it the batteries of these chips gone dead. so i replaced them with new DS1230Y-150 chips. The machine was booting up right...
Now i replaced them with new DS1230Y-150 chips as mentioned in another post. The machine was booting up right except when changing tools or wanting to make a new programm it hang up on me.After...
ok I have a client with an old Hurco Ultimax II. The machine powers up fine. always able to calibrate (home) the machine. all tool changer movments work in diagnostic mode.
now the problem
when i...