501,873 active members
1,033 visitors online
Register for free
Login

Search:

Type: Posts; User: regina

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Thread: fanuc om help

    by regina
    Replies
    1
    Views
    22

    Re: fanuc om help

    Memory data is gone for sure. Hard to say if you messed up anything else. How does the display look if you have the batteries out completely? If it is Also, Is this a A. B, C. or D? Not sure if that...
  2. Replies
    0
    Views
    23

    fanuc 6MB2 Parameters

    I am trying to transplant the color mdi/CRT/softkeys and graphics card from one machine that is being scrapped to another one that I intend to use that just has the basic small monochrome mdi/crt...
  3. Re: Alarm EX1012 IN THE TOOL CHANGE AREA (Fanuc Robodrill ?-T21iFa)

    I think you may have reset the turret, but the head is up too high in Z and is in the area normally reserved for tool change. This can happen when interrupt a tool change in progress. I pulled my...
  4. Replies
    3
    Views
    46

    Re: Need shipping weight of a millac 4va

    Got it home safely today. Manual lists at 12,125 lbs but I think that is without the control. I would estimate it was about 14,500 for anyone's future reference.
  5. Replies
    3
    Views
    46

    Re: Need shipping weight of a millac 4va

    Anyone? I have to go and pick it up tomorrow.
  6. Replies
    2
    Views
    59

    Re: Replacing a pulse coder on Fanuc 0M mill

    Yes it must be timed to the motor. This has been addressed here before. The instructions are in this post:

    https://www.cnczone.com/forums/fanuc/258532-procedure-installing-fanuc-pulse-coder.html
  7. Replies
    2
    Views
    41

    Re: Fanuc 15MA MDI types

    Thanks, that at least gives me an idea how it works. I wonder why they made so may variations instead of just having every one populate the full matrix. So much skipping around. Where in the...
  8. Replies
    2
    Views
    41

    Fanuc 15MA MDI types

    I was wondering what it takes to use the newer style MDI ( https://www.dnc-electronics.co.uk/parts/fanuc-monitor/crt-mdi/a02b-0162-c092/ ) with the 15A. The older one with the membrane keysheet looks...
  9. Replies
    3
    Views
    46

    Need shipping weight of a millac 4va

    Hello all I just bought an old millac 4va and need to figure out how heavy it is to ship it home I've seen weights listed from 12500lbs to 17000lbs what's the real deal?
  10. Replies
    2
    Views
    50

    Re: system P-G disk format

    Thank you drdos! I was able to successfully format the disk and back up my file :)

    Someone else also shared some other commands with me and I thought I should share them here in case someone else...
  11. Replies
    2
    Views
    50

    system P-G disk format

    Does anyone happen to know the command to format a blank disk from the "request" line? "format" doesn't work.
    It won't let me save to a plain blank disk. I assume I have to format it first.
    ...
  12. Replies
    4
    Views
    71

    Re: Fanic O-T retrofit ease

    In a semi related topic I have some nice PCI and ISA Galil motion control cards, cables and breakout boards along with the industrial motherboards to run them with mach I bought when I thought about...
  13. Replies
    4
    Views
    71

    Re: Fanic O-T retrofit ease

    From what I'm learning none of the retrofit stuff is "easy" unless you buy something like a centroid that is pre configured to your application. You are going to have to find out more information...
  14. Re: Need hardware descriptions manual for 15MA and PCM N manual

    I got the idocs mailed to me, but there are very few manuals for the 15A in it :(
    I bought the GFZ-61222E 15 MA descriptions off ebay but it looks like I will still need other manuals to find out...
  15. Re: Feeler Mill QM22 - Fanuc O-MD Control - Error 1330 MAG CTR SENSOR ERROR

    Not to sound dumb, but did you look for a mag sensor/s to see if it/they have chips or anything on it? Are you cleaning with compressed air? That would be a likely culprit. Or else test it some how?...
  16. Replies
    27
    Views
    338

    Re: Fanuc Series 3 AC Servo Amp - Failure

    Following with interest. I have one of these drives I will need to use in the intimidate future. What manual and schematic are you guys using to troubleshoot?
  17. Replies
    2
    Views
    79

    Re: Help with Fanuc 401 Error

    I have had the 401 error in the past. You don't say what SVM you are using but it sounds newer than the 6058 and 6066 I was dealing with. Your pics are not working showing your cabling and jumpers....
  18. Re: Need hardware descriptions manual for 15MA and PCM N manual

    I do now. LOL Fortunately GiGs aren't that heavy. :) I think I may have found someone who can snail mail it. A generous member shared the I/J and the N manual with me. Thank you sir!. I can...
  19. Need hardware descriptions manual for 15MA and PCM N manual

    I called Fanuc and tried to order the IDOCS DVD and they said that it was only carried by GE fanuc and that company no longer exists and it is not available through fanuc America. I'd gladly pay...
  20. Replies
    6
    Views
    149

    Re: FANUC 18 Model C Build (FS18TC)

    I haven't really dug into the yellow plastic box controls yet, but I have a couple so it is good information to have stored away for the future. May as well include the versions of software you are...
  21. Replies
    1
    Views
    55

    Re: Probably dumb FS6 vs BMI questions

    Looking at it now I see there is a board called the "connection unit" that resides in the pendant. The regular M1 and M2 50 pin connectors from the op panel connect to and that board converts the...
  22. Replies
    20
    Views
    245

    Re: 0-ma 2nd communications port?

    Well that's encouraging at least you know the control is seeing the inputs. I don't suppose you have paper ladder print out to help you correlate as to what inputs should produce what outputs address...
  23. Replies
    20
    Views
    245

    Re: 0-ma 2nd communications port?

    They worked before, I doubt they would just choose to mess up now. Man, that is frustrating :( I hope it is something easy like a mis-seated cable or something. Even though you can't see the ladder...
  24. Replies
    1
    Views
    55

    Probably dumb FS6 vs BMI questions

    I apologize as I know this has been covered a thousand times here. From what I understand the Fanuc 0 series controls use FS6 addressing. Is this still true for the versions C and D? Is there any...
  25. Replies
    20
    Views
    245

    Re: 0-ma 2nd communications port?

    Yes the op panel is run my the pmc, so it probably won't work until you get the pc paramaters put in. That sucks on the chips. only thing I can think of is to look carfully for any briged pins from...
Results 1 to 25 of 112
Page 1 of 5 1 2 3 4