584,814 active members*
5,331 visitors online*
Register for free
Login

Search:

Type: Posts; User: mflux_gamblej

Page 1 of 17 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    781

    Re: Fanuc 16iA, SRAM Memory Card Backup

    you need to get an SRAM card that has a battery inside. they were made by a lot of companies but now they're rare. ideally you'd get one that is larger than your sram (512K or 1MB or 2MB). these...
  2. Replies
    0
    Views
    162

    Fanuc 16i, want to DPRNT to card

    I have renishaw probe macros. I am wanting to DPRNT to a card.

    I have already run into a couple hang-ups using the macros that I have. O9730 ren print, it has a line such as...
  3. Re: restored from SRAM, but param are still messed up, issue with program protect sw

    the machine is back up and running. it turned out that my backups were corrupt and I needed to get the ladder data in a file that was not corrupt. both my ladder and sram backups were corrupt. my...
  4. Re: restored from SRAM, but param are still messed up, issue with program protect sw

    it was confirmed by someone with fanuc ladder iii that my ladder backup file is corrupt. if anyone that has a robodrill circa 1997-2002 with a 16iA control, I would really appreciate it if you could...
  5. Re: restored from SRAM, but param are still messed up, issue with program protect sw

    have tried a different motherboard but get the exact same behavior
    have tried a different sram board just in case its messed up, but no its the same behavior

    i have been on the phone with...
  6. Re: restored from SRAM, but param are still messed up, issue with program protect sw

    I'm pretty certain after continued hours spent on this that the core mistake was loading a .LAD file in IPL mode from a .LAD file that was generated in the PMC screens when the machine was working. ...
  7. Re: restored from SRAM, but param are still messed up, issue with program protect sw

    additionally regarding the two (right hand) buttons IPL menu. i probably f* up when I read in the .LAD file from my sram card there. The .LAD that I have is one that I read from the PMC screens...
  8. Re: restored from SRAM, but param are still messed up, issue with program protect sw

    i have this to a point where i can load a ladder, and pmc parameters onto the machine, when I hit RUN on the pmc, i get a 975 bus error.

    the pmc is not running, and i do suspect that the program...
  9. Re: restored from SRAM, but param are still messed up, issue with program protect sw

    I did (probably stupidly) load a .LAD file in the two left buttons boot menu. this should be just fine, as i got the .LAD file from the same boot screen at an earlier time :) I don't yet have a...
  10. Re: restored from SRAM, but param are still messed up, issue with program protect sw

    i was able to load the parameters over rs232, this issue was that one of the parameters in my restore file changed the io device from rs232 to mem card, and that change instantly stopped the flow of...
  11. Re: restored from SRAM, but param are still messed up, issue with program protect sw

    there are two scenarios happening: 1.) restore from sram card, this allows access to quick/nc screen but it just keeps saying the change the protect switch, in this case, I cannot access the PMC at...
  12. restored from SRAM, but param are still messed up, issue with program protect sw

    I have a robodrill with a 16imA control, I lost my params due to messing around with the mobo after I got a sysfail led. This turned out to be a psu that died in the ctrl cab behind the i/o board. ...
  13. Re: Fanuc 16iM, on a robodrill, won't M99 repeat, won't even GOTO1 to N1

    this one is solved. it had nothing to do with the pallet call program.

    it was my part programs, which get posted out of my cam software with an M30 at the end. since this pallet change call...
  14. Fanuc 16iM, on a robodrill, won't M99 repeat, won't even GOTO1 to N1

    I have a robodrill w/APC and am trying to run a program

    %
    O0001 (CHANGE PALLET CALL PROGRAM)
    (SET PROG NO FOR EACH PALLET IN QUICK NC)
    M65
    M98 P#990
    M01
    M99
    %
  15. Re: Replaced stepper drivers, now raster engraving is messed up.

    I will add that I have reverted to the DM545A stepper drivers that were on my machine from the factory. Without changing anything but this, the engraving is spot on. I kept my new 48V supply, and...
  16. Re: Replaced stepper drivers, now raster engraving is messed up.

    did you ever solve this? I did the same thing, and now have the same result as you with timing being off. no setting seems to help. I have tried changing the phases A swapped with B. I have tried...
  17. Replies
    0
    Views
    271

    10T control, cycle start twice?

    for some reason on my mori sl-0 lathe with a 10T, I have to press cycle start two times to get a program to run. anyone know which parameter to change to get this behavior to go away?
  18. Renishaw Probes, 'full package' for Fadal, could go on any CNC though

    https://www.ebay.com/itm/133774649193
  19. Replies
    3
    Views
    781

    Fanuc 16iA, SRAM Memory Card Backup

    I have a robodrill with a 16iA control. I had some problems recently and ended up with a 'ghost control' with all params deleted. Luckily on this control all the params, ladder, and even macro...
  20. Re: robodrill at14ia, 16iM control, need backup from another machine, params, ladder,

    for anyone who ends up here, back up your system on to a cf card Now

    anyone for who its too late, i lost my pallet change macro code (lucky i had a paper copy), the default params were wrong for...
  21. Re: robodrill at14ia, 16iM control, need backup from another machine, params, ladder,

    this is mostly solve, under quick NC, restoration, there are params, pmc, macro, custom params, cap settings backup. lucky me. just have to double check the params now, take a couple hours to make...
  22. robodrill at14ia, 16iM control, need backup from another machine, params, ladder, etc

    Does anyone have a robodrill at-14ia and can make a copy of your sram using the boot system and send it to me? I had a working robodrill, but it gave me 911 parity error, and since then, I haven't...
  23. Replies
    14
    Views
    3,104

    Re: Fanuc 16iA, skip input for probes

    I got it working.

    it was the honda connector, I had pin 1 and pin 3 soldered, assuming that the top row was pins 1 2 3 4 etc, but the top row is 1 3 5 7 etc. Found this out by ohming out a spare...
  24. Replies
    14
    Views
    3,104

    Re: Fanuc 16iA, skip input for probes

    I have also tried setting 6200 bit 5 (SRE) to 1 for use with the falling edge, that makes the G31 behavior the opposite, so the machine will move, but the there is no effect for closing the relay...
  25. Replies
    14
    Views
    3,104

    Re: Fanuc 16iA, skip input for probes

    I was able to see the status of output Y0002.1 change as I turn it on with M100 and off with M110. So, it looks like the HSS signals as shown by F122 are all on F122 has [IIIIIIII] and there is no...
  26. Replies
    14
    Views
    3,104

    Re: Fanuc 16iA, skip input for probes

    I have this all setup for hss, except, when you do a G31, the machine goes nowhere.

    I have set the params for the skip function in the 6200 range:
    ------ 76543210
    6200 00010000 (bit 4 set to...
  27. Replies
    14
    Views
    3,104

    Re: Fanuc 16iA, skip input for probes

    this is working, that terminal block is XT5, terminal 12 is for input x4 bit 7.

    I couldnt get the PMC display to show the status of this input, I hooked pins 10 and 12 together to put 24v on the...
  28. Replies
    14
    Views
    3,104

    Re: Fanuc 16iA, skip input for probes

    I also found this in the setup page for inputs, I set 4.7 to 'skip'.

    I'll hook up a switch or something to pin 12 on that terminal block, see if I can get the input to display its status somewhere...
  29. Replies
    14
    Views
    3,104

    Re: Fanuc 16iA, skip input for probes

    I assumed that the terminal block in the control cabinet was an option terminal block related to the pallet changer. Maybe this is not the case as all the i/o to the pallet changer goes thru honda...
  30. Replies
    14
    Views
    3,104

    Re: Fanuc 16iA, skip input for probes

    I see this page from the connections manual, which describes X0004, Bit 7 as the skip input.

    I see that the connector CE57, Pin 09B is called Xm+4.7, I assume this is related.

    How does one...
Results 1 to 30 of 500
Page 1 of 17 1 2 3 4