Search:

hi
yes i know all that for this controller. when it goes to close loop it will in problem. i have checked the teco and adjusted but same . and also set the gain in parameter n on drive. but same
...

hi
what type info u need?
all axis have huge vibration.
when going to ref its normal. after ref complete motor vibrate and gross positioning d error.
i checked all axis separately.

all axis.
if i change control then normal.

Hi
I have problem in TNC 151. Machine axis goes to reference point normal but after reference it vibrates heavy and gross positioning error.
Any kind of help appreciate.
M. Shabbir Mughal

Hi all
I have machine with BMDC3SV REV C . I want it's software. Any one have please send me.

hi all
i have machine TV30 with MSC-802. all good but all axis going in positive direction. when i move in -ve the error. M01 operation error 0007.
any one can help me here?
what is the procedure...

in turning center tool change command is M6 T0101
and in machining center tool change command is M6 T01.

in lathe T01 will not work correctly in mach3
thanks

hi
i m also working on this machine. GV2518e is not communicate with machine with original settings.
i m repair n maintenance man for cnc for hardware n software side. i check the machine there is...

Thanks Mihia
I understand it.
1 shl cs20 = set bit cs20 or cs20=1

dear Mihai
yes i have some question .
if u dont mind n have time send me details of this.

in
// PWM channel 0
TCCR0A := (1 SHL WGM00) or ({1}0 SHL WGM01) or (0 SHL COM0A0) or (1 SHL...

dear mihai
please help me to conversion firmware from mega644 to mega2560. .
pin mapping changing. because i m not familiar to pascal.
shabbir

hi
i buy arduino but i m not using arduino software for programming.
i m using avr studio. n then upload hex from isp r usb cable.
thanks
shabbir

arduino is the best i feel because it is available in all countries.
and noe made smd pcb .
i m also trying this in arduino mega 2560

shabbir

hi all
today i finally purchased all components for this.
now i will try to complete this in this week.
IN SHA ALLAH.
also i have to modify this for atmega 2560.
shabbir

Dear Mihai
yes
u r good programmer u can implement. its very nice for all. that we can use normal only ab r abz encoder for bldc.
i was just study why uvw encoder use. that i understand.
all ok...

hi all
i found this another forum then i understands all bldc commutation signal where use.
"""
At power up, the UVW signals are present and they provide a low resolution "absolute position"...

hi Mihai
please upload a video latest power on off n running.
thanks

hi Mihai
it a grate success .
keep it up.
thanks
shabbir

Hi Mihai
I get the mikropascal 4.6 .now finally decided to use mega 2560. As is Ur firmware. Mega2560 n 644 same price here.
But I want to learn little about Pascal
Shabbir

hi Mihai
thanks for info but a little problem more. i m not familiar to pascal .
help me in that u have said.
thanks

hi Mihai
can i use ATMEGA 162.
it has 16 kb flash
6 pwm 8bit
shabbir

HI Mihai
no no
i wants only that when we apply the motor power to drive it would not to free run for calibration..
shabbir

Hi Mahai
U r right on step missing but when recalibrate the servomotor it rotates for calibration. This is problem .
I feels don't rotate the motor at calibration.
When any drive gets commutation...

Hi Mihai
i have some motors for experiments .
Panasonic 96 vdc encoder 1024 pulse no commutation. 200watts 3000rpm 8 poles
yaskawa 100vdc encoder 2048ppr 100watts 3000rpm 8 poles
yaskawa 150vdc...

Hi Mihia
Thanks for reply. Now I start study of Ur last firmware.
One question more.
All 3 phase a.c. servo drives use commutation feedback must. But in here it is not used.
I m feeling...

hi
i want to make this but here atmega 644 is not available. but i can found atmega 2560.
help me for this.
also available atmega 88 n 162.
shabbir

hi all
can i use these all on near about 200 vdc servo motor . 1 kw.
shabbir

hi all
if i want to make this cnc controller then where i fount its material. hardware and software.
shabbir

Dear friends
when i on the machine on screen it shows
E09-001C E09-001C
CHARACTER RAM OK
FIFO READY
WORK RAM OK

beaver machining center with color screen control fanuc 6m.
no key work. only...

HI all
i have dead makino FX650. i want to start it. i required its spindle motor details. it is 8000rpm and 6 leads for power. may be double speed. any one can tell me if he have this type of...