Thanks for the information!
It was corrupt parameters in the OT Control itself, most likely due to low batteries.
I put new batteries in, found a copy of the "As-Built" parameters and hand typed...
Type: Posts; User: smyers755
Thanks for the information!
It was corrupt parameters in the OT Control itself, most likely due to low batteries.
I put new batteries in, found a copy of the "As-Built" parameters and hand typed...
We were in the middle of running parts on our 2006 Fanuc O-T Control Femco CNC Lathe when it shut down with an AL-34 PARAMETER SETTING ABNORMAL alarm.
No one was changing any Parameters on the...
Sorry, I should have mentioned that the photo is just to show the orientation of the XYZ origin on the tombstones and does not represent the actual parts.
That's a tombstone I found a CAD file for...
Just to be clear, the parts are orientated flat at 90 degrees, parallel to Y, perpendicular to X and Z
When I mentioned tilting the head on a MCM and using M76, the tilt would be a full 90...
Reading this GAUGING SYSTEMS Manual you posted makes me think Okuma has the ability to X-Z probe, but it's most likely not provided on 4-Axis Machines.
They talk about using M76 to swivel the head...
Thanks for the Manuals, that helps a lot!
As far as what I need to do with the Renishaw Probe is, I have a L-Shaped Probe that can reach inside the bores shown in the attached pic.
The Bore is...
This option was ordered at the same time as the three Machines, but no manuals were included.
The last Programmer said he got all the information doing Google searches and calling Hartwig support....
Just in case anyone else is interested in X-Z Diameter Probing using a Renishaw Probe:
Renishaw got back to me and said it is available.....but only for Fanuc and similar controls like Haas, NOT...
:violin:
I've gone through every User Manual stored on the hard drive in the Machines and even found a Factory sealed large box with 15+ Hard Copy Manuals - but none of the manuals mention two...
Has anyone figured out how to use a Flat Star or Right Angle Probe on a CNC Mill using GoProbe or other Renishaw probing routines?
Our fixtures hold parts with bores in the Y-Axis on the...
After searching online, I read that Okuma supplies all the manuals for each machine on the actual machine in electronic format.
Can someone explain in detail how I can copy those onto a USB stick?...
OK, thanks to deadlykitten I spent the last few weeks reading the OSP-P300 Control manuals and I can now understand the code their Mastercam/Okuma Postability post is putting out for the Okuma...
@deadlykitten
Thank You !
Does anyone know where I can download a Programming Manual for the OSP-P300M control?
I've been offered a job in another state, but my 25+ years of programming has always been Fanuc Controls and I...
First off, I know this is a very old thread, but it's also in the top of a Google Search for formatting a Compact Flash Card for Fanuc Controls.
After spending a lot of time in Trial and Error, I...
I know, old thread but maybe someone still has the info.....
I need the 900 parameter list for an 0T control.
Thanks in Advance
Thanks for the replies so far.
We are not using any Bar-Feeders, we are using grip style Bar-Pullers and short pieces of stock.
We cut 48" long bars (1220mm) and they fit (mostly) inside the...
Maybe I'm wrong, but I would think because I don't get an error when I manually step on the clamp/unclamp pedal that the sensor would be fine.
If someone has a Manual and could look up the...
Does anyone have a manual for an Akira Seiki Lathe with a Fanuc 0T control?
We are trying to use a bar-feeder and every time "in-program" we open the check to feed (M11), the machine errors out...