Sorry, I have no news on that topic. A workaround is to make multiple cnc files.
Type: Posts; User: electracks
Sorry, I have no news on that topic. A workaround is to make multiple cnc files.
Can you please send me your Mailadress or website or postal address by PM? These pictures look also like BCAMCNC stock photos. Although they are better made, because this time there is no chinese...
Hey Marc,
Please tell your boss he should handle my complaints and offer a solution. This is better than trying to disgrace your customers with fake accounts in this forum here.
I wonder why you use chinese calendars in Germany, see picture 1/ right top and why you have a chinese forklift in an obviously chinese neighbourhood see picture 2?!
Can you please somehow prove your identity? Website, Email, Adress or so?
It is interesting how many people made a new account to answer this thread and stating how good BCAMCNC is. This makes me a bit suspicious. Hey, BCAMCNC this is not the way to handle complaints. You...
I am a competitor? LOL! I wanted to resell their machines here in Germany but the quality is so horrible, no one will buy this from me. I already resell Thunderlaser and I know what to expect from...
Can you show me some good feedback about BCAMCNC? I did not find anything.
I contacted them. I already posted in another thread that their solution for me was that I buy another machine from them and pay in advance. That was the only solution they will offer. They even do...
Well the only thing they offered was sending me a new machine at a small refund with payment in advance! LOL!
They admitted that one of their workers smashed the machine into the wall and they sent it anyways. This is not only a cosmetic thing. Nothing is parallel anymore. Please tell me how to fix this....
This is not normal chinese quality. Even chinese quality is normally much better. This is a fraud!
I informed them that I am posting here. "Jason" is very disappointed and sad, he wrote me. He fears that his boss is loosing trust in him....
It is very interesting that there is no reply here...
Another big problem is that I asked many times before purchase if this machine fits through a 90cm door and always their support said that it will fit.
When the machine was delivered it was 110cm...
One axis is somehow loosing steps:
http://www.cnczone.com/forums/attachment.php?attachmentid=313724&stc=1
The oil system is leaking:
...
This is a bearing below the table. You can see how much metal chips are building up at the bearings. It will take only a short time until this bearing dies:
Again, please remember this is a unused...
I found a thread cutter near the rails, blocking one axis:
313718
There is a screw and I can not find where it belongs:
313716
They also did not deliver any machine or controller manual, No filter bag for the exhaust system and the compressor for the coolant spray was also not delivered.
This is also a nice one:
313712
The machine goes on when you switch to "Off" and it goes off when you switch it on
Here it seems like they had not enough paint left:
313704
Fun Fact: The emergency stop does not cut off the power of the machine. It only stops the movement of the motors.
More pictures of...
This is also a rail of the machine. It was painted!
313698
Here is another part of the paint job. The electronics were painted too:
313700
So lets continue this.
Here you can see the rails of the machine, they are covered in metal chips and it is very likely that metal chips are already inside the bearings:
313694
This is the...
So I think this was enough for one day. To be continued tomorrow.
I hope someone from BCAMCNC will reply to this. I know they are active in this forum so this is their chance to make it right.
Then lets have a look at the screwholes they made....they should be round and this is what they look like:
313586
This is how most of the covers look like:
313584
Many screws are squeezed into poorly cut threads, damaging the screws and the threads. It is not possible to put a screw correctly in there.
...
This is the curtain. BCAM claims to offer high quality but it looks like they even can not handle scissors...a 3 year old child can do better
...
This is below the table. It seems like there was a small gap and the solution of BCAM was not to fix the table alignment, but to stuff something into the gap making it even bigger. Now the table is...
Here is a view of the table. Please remember that I ordered a new machine not a refurbished or used one:
313572
313574