Search:

Sorry for a late reply, I'm using MACH4 but I can't imagine that it would be that much different from MACH3.

https://www.youtube.com/watch?v=d-xCWDR0Uvg

This video describes a process of how...

under mach4 output looks looks like this now https://imgur.com/a/Ot4BJSY
and under ESS looks like this nowhttps://imgur.com/a/EK47Jev

If I try to do green check mark on ESS output signals,...

I cant turn forward on.

Ok this is where I feel lost.
I do not understand relationship of ESS pins input, pins output and MACH4 pins input, pins output. I know this probably feels simple to most...

Thank you very much for helping me get this going!!!

This is how the ESS looks nowhttps://imgur.com/a/vK0l8TZ
and mach4https://imgur.com/a/3tJfHFi

YES!!

Switching jumper to 2-3 position and

PD000=0
PD001=1
PD002=1

was able to start and stop spindle in mach4 and was able to change rpm with dial on VFD:)

Ok I tried :
PD000=0
PD001=0
PD002=0
nothing happens

I tried
PD000=0
PD001=1
PD002=1

Ok, my mistake.

I only connected FOR and DCM and corrected PD001 to 1 and have this settings now

PD000=0
PD001=1
PD002=0
PD003=400
PD004=400
PD005=400

Ok, so im going to take my existing parameters and change to the ones you gave me at the beginning of this tread

PD000=0
PD001=0
PD002=0
PD003=400
PD004=400
PD005=400
PD006=150
PD007=20

OK! i got something right!

I did continuity test on CM3-FOR and NO3-DCM and i get beep on spindle ON, and no beep on spindle OFF.

i also was looking in mach4 (configure-control-spindle) and...

Ok, i have fixed this now.
i have:

AO on mb3
AG on mb3
CM3 on mb3
NO3 on mb3 (the NO3 light on MB3 comes on during M03 S12000)

No vires are connected to VFD

That is the problem Mactec54, I did read the manual I just don't understand it.
Are this pictures better, https://imgur.com/a/wER8Ve9

Ok, I have disconnected wiring to VFD for now.

In attached pictures you can see my ESS and MACH4 settings.

If I go to MDI and start spindle M03 S12000 I get 10v and the light on AG AO comes...

The spindle is Huanyung 2.2 kw water cooled spindle HY02D223B

I got help from wessongt on reddit on how to wire it and I got it wired but not sure what to do in mach4.

i have wired:

AO on mb3 is going to Vl on vfd
AG on mb3 is going to ACM on vfd
CM1 on...

Hi everybody,


I'm wondering if I can get some help from somebody who might have a similar setup.


For the past year I have been slowly putting together my CNC and with the help from all the...

Hi everybody,

I am making progress on my DIY CNC, I have everything hooked up and it seems to be running well. I have actually made my first cut in three-quarter plywood. My feeds and speeds are...

I was going to the same thing. I was going to bring 110 and 220 to my control box but now reading this I'm not sure how to do this. My 220 does not have neutral wire just 2 black and the ground. How...

Thanks for your reply Restless1,

That is how I ended up wiring everything. The only difference is that I have a different power supply ANTEC PS-10N80

Right now I'm working on my control box...

Thanks for your reply Abe,

I will consider this when I build the frame out of the metal.

My machine right now is built out of the wood so I'm not sure that I can use my "stops" as my homing.
...

I am slowly inching forward in building my first cnc.

I'm using ESS/MB3 combo with clearpath CPM-SDSK-3421S-RLS motors.

I am almost finished installing hard stops. I have temporarily wired all...

Is there anybody that can help me with wiring?

Thanks for your reply Craig,

I think i know now, i have my power and motors connected right so the next step would be to connect E-stop. I have my MB3 manual on my one drive here...

My power supply is ANTEC PS-10N80 https://www.antekinc.com/ps-10n80-1000w-80v-power-supply/

Beter picture of wiring.

https://imgur.com/a/Y50i3QU

Hi everybody,

I am looking for some help with the wiring of my motors and the board. I have purchased four stepper motors, four drivers, linear power supply and the power supply for my MB3/ESS...

Thanks Craig,

I think i'm going to go with power supply you suggested.

Just got of the phone with Leadshine customer service and and the guy I spoke to seemed very nice and helpful.

I was trying to get more info on D57CM31 motors and EM882S drivers. The motors are...

Thanks Gerry,

I think i had a brain freeze when i mentioned i need 24v PS for ESS, i ment mb3.


Darko

Thanks Craig,

I just received my ESS and MB3 board and i'm trying to read everything. From looking at stuff online ESS plugs directly in to MB3
I think i want to build everything on DIN rails.
...

Thanks Peter,

I will see if i can incorporate your suggestions.

Thanks for your advice,

I was looking at that power supply and noticed model PS-10N80N24, I'm assuming this one is giving me 24v also to use on my ESS? Do you think that is ok to do or should i...