Search:

302050302052302056
Sorry about the watermarks.

Hello, page 9-27 9-28 9-29 are the parts lists for Series 1 CNC Head R-Ram. Yes 9-31 is the last of the parts list. If you send me your email in a private message I will try and send you a copy if...

Hello, I'm looking at purchasing an old Brown and Sharpe Gage 2000 CMM that's missing the control unit. I was wondering if anyone knows where I can get one or does anyone have any ideas what it could...

Sometimes when I try to open a new art base surface from image I get an error that says "Failed to create temporary file" then "Error in JPEG-library!"
Some photo's work and others don't. Any reason...

I have my Sigma motors wired in parallel as follows: terminals 4+8, 2+7, 3+6, 1+5 are connected. I am using the automatic oiler filled with a light weight oil that seems to flow pretty good. I have a...

Please check out the video on my other thread "Bridgeport stepper motor trouble VIDEO" . First hand on what its doing and sounds like. What puzzles me most is that last summer it was fine but now...

I don't have access to a scope unfortunately. The thought of trouble with the ball screw did come to mind. I took the Y axis motor off and turned the ball screw pulley freely through the travel....

Nothing new has been added to the computer. I have recently updated to a newer version of mach3 but I was having this same issue before the update. Not sure if the driver would update automatically.

I ran a program to warm up all three axis. It got to around 30 ipm before it started to make the sound again and loose steps. Really didn't sound smooth at any point. Program ran for about 20...

It is cold. I was wondering if that was a factor. Here in Missouri its still hanging around 40 to 50 degrees. I will write a program to give it a good warm up and see how it does. Thank you for the...

I'm using gecko 203V with 7 amp output at 72 volts. No changes since it worked last summer. I've tried different speeds and accelerations but no luck. Went back to 25,000 kernel speed but it didn't...

http://www.youtube.com/watch?v=y2cRx3Gw6QE

Added a video on what my sigma steppers are doing. Has anyone experienced this before and if so how did you solve it?
Mach3 tuning: Speed 60, Accel 1,...

91 views and nobody has feed back on what they have their bridgeport steppers tuned to in mach3. Come on don't be shy !:wave:

Hoping to get feedback on what people have had success with in Mach3 motor tuning with Bridgeport steppers.
I am running with a 72 volt power supply, gecko's 203V at 7amps. Bridgeport Sigma stepper...

I wish I could help you but I can't get mine to work either. I also had to add a secondary parallel port card. In my case I am using the c32 bob with the pendant connection built in. I'm happy with...

At first when I ref Z it did the same thing as usual but the M1 lights on the diagnostic screen lit up. That told me right there that my X and Z pins were reversed. Sometimes frustration gets the...

I have the gecko 203v running my existing Bridgeport steppers. Just finishing up the retrofit and have yet to make CHIPS.
My limit switches plug into a C32 breakout board from cnc4pc. The limit...

Hope this helps.
I had to run my limits through parallel port 1, having trouble with port 2. Anything that is currently set through port 2 should not be active at this time as you will see in the...

My limit switches plug into a C32 breakout board from cnc4pc. The limit switch LED's show on the breakout board as well as on the diagnostic screen in Mach3 when activated. Everything seems to be...

Hello
I have a Bridgeport Boss 4 retrofitted with C32 bob, using existing limit switches wired NC with 5 volt power. I have xyz +-home enabled and active low, port and pins 2-12 2-13 2-15 are used....

You can find the answer at http://www.cnczone.com/forums/bridgeport_hardinge_mills/146609-gecko_203v_bridgeport_stepper_wiring.html
Its all good !! got my sigma's wired up and they zip along.
The...

Thanks VFD runs great!!!

In the manual it shows 3 inputs: U1 , V1 , W1. It says when using single phase use U1 as (L) and V1 as (N) W1 has no connection. So am I to understand Al_THE_MAN that I should hook one leg of...

Hello all. I have a VFD manufactured by ABB ACS150-01U-07A5-2. It is a single phase 230 input with three phase output. I am a little confused about hook up. I am retrofitting a Bridgeport series 1...

Found a diagram for bridgeport stepper wiring in parallel. I have not tested this but will update findings when retrofit is complete

Thanks! I actually found this setup on another post but was looking for clarification. Would this be a parallel wiring ?

I have the Sigma motors

Looking for BP stepper motor parallel wiring schematic with phase connection to G203V drives. :confused: Been lurking awhile, haven't found a straight forward diagram. Thank You

Looking for BP stepper motor parallel wiring schematic with motor phase connections to Gecko 203V drives. Having trouble finding a straight forward diagram. Thank you !:confused:

THANK YOU, THANK YOU, THANK YOU, for the replies. Any chance on getting the make and model of the servo pictured by mactec54. I was concerned about this do to the responses that the Keling servo's...