584,817 active members*
5,124 visitors online*
Register for free
Login

Search:

Type: Posts; User: bkobernus

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    1,590

    Re: HAAS VF0 Mastercam post need

    What version of MasterCam?
  2. Thread: sprue puller

    by bkobernus
    Replies
    4
    Views
    3,839

    Re: sprue puller

    go here: https://na.dmecompany.com/Catalog/CatalogListing.aspx?CatalogId=DME&CatalogDetailId=357&NSM=Y Download the cad model of any of these sprue puller bushing, and copy their geometry.
  3. Re: Dyna Myte 4400M with Meldas M3 Control. I think the battery is dead

    Well, Good to hear that you found your problem. Also good thing you got that tool out before you tried a tool change, 'cause the first thing a Dyna does for a tool change is DROP whatever is in the...
  4. Re: Dyna Myte 4400M with Meldas M3 Control. I think the battery is dead

    I run mine with a 5HP Roto-Phase, phase converter. I have found that, that would be the minimum size phase converter, as the machine is very voltage sensitive. If I turn on, or off another machine...
  5. Re: Dyna Myte 4400M with Meldas M3 Control. I think the battery is dead

    Attached Photos of wiring of Clamp/ Unclamp switches inside front plate of head.

    I never had the Y axis thing happen to me, and I shut my machine down with the Y axis in the full Y- direction. I...
  6. Re: Dyna Myte 4400M with Meldas M3 Control. I think the battery is dead

    MrMetric,

    Sorry for the delay in reply. It's been a busy year.

    Just read you post. Sounds to me like one of the Y limit switches is stuck. That's why the Y axis moves only in one direction....
  7. Re: Dyna Myte 4400M with Meldas M3 Control. I think the battery is dead

    Is the magnetic switch working on the carousel? I would check mechanical before blaming software.
  8. Re: Dyna Myte 4400M with Meldas M3 Control. I think the battery is dead

    It's been so long, that I would have to review my notes, and then actually sit at the machine and figure it out. Other wise you just have to go through all of the parameters manually.
    I have all...
  9. Re: Dyna Myte 4400M with Meldas M3 Control. I think the battery is dead

    Hi Jim,
    I'm glad that the files helped you out. Where are you located? I'm 40 miles west of Chicago. When you get yours working, feel free to stop by and get running. It's been sitting dead for...
  10. Re: DM4400-what size 3 phase motor for rotary converter

    Drhanger,

    I've been reading over you post. You are in the Phoenix area? You should be talking to this guy: mc-machine.com - Home His user name on this forum is "Capri". He has a few of...
  11. Re: Determination of year of build, DM 4400 with Mitsubishi controll

    RAC917,
    Congrates on your new toy.
    I don't have any idea on the exact year of your machine, but I also have a DM4400M with Mitsubishi Meldas M3 Controls. I have all of the books.
    I answered a...
  12. Re: Dyna Myte 4400M with Meldas M3 Control. I think the battery is dead

    Patrick,

    Hope you got your machine running. If not, Sorry I'm so late in getting to your post.

    Attached are files to get you up and running if it IS a dead battery situation.

    Files include:...
  13. Looking for a Moldmaker or Machinst, Downers Grove, IL

    Moldtronics Inc., a custom injection molding company,located in Downers Grove, Illinois, is looking for a moldmaker or machinist. 1st Shift. MUST have CNC Experience. Working Knowledge of MasterCam...
  14. Replies
    1
    Views
    879

    Re: Prototrak mill

    Randy,
    Since no one else has replied, I will.

    Prototrak bed mills, or even just a Prototrak mills should be in every shop. They are, and have been, very popular for the past 30 years. The...
  15. Replies
    6
    Views
    634

    Re: Prototrak Plus manual

    Simracn,
    I'm sure I could find a manual, scan it and send it to you..... BUT where are YOU. Nothing in you profile for location.

    Not in USA....... = NOT getting copy of manual.
    ...
  16. Re: Mastercam X6 toolpath crossing geometery

    J,
    My first question... Contour 3D? Are all Entities lines and arcs in a flat plane. Are there multiple entities that are exactly on top of each other? On chain or multiple chains?

    Bill K
  17. Re: Norgren Gear Change Solenoid - Gear Change Issues

    Jim,
    Just call Haas, in your area. (where is your area?) They will know, and give you, the part # based off of the S/N of your machine.
    Part #'s are something I just don't think about. Being...
  18. Re: Norgren Gear Change Solenoid - Gear Change Issues

    You are correct. You cannot just purchase the Norgren valve from Haas. You must purchase the entire assembly. I think it's around $200. In the long run, you'll be better off just buying the whole...
  19. Replies
    4
    Views
    1,884

    Re: Lettering on a Sphere?

    I think there is two ways of doing this.
    Create letters on a flat plane, above or below your sphere surface. Use Xform, Project, to project them onto the sphere surface. Then cut them as a 3d...
  20. Replies
    14
    Views
    20,835

    Hey Look at that. I knew you could do it. Only...

    Hey Look at that. I knew you could do it. Only took 2 months to find that leak. Not bad.

    Soon you will qualify as a Haas repair tech.

    The next problem you will have is the x axis always goes...
  21. Replies
    2
    Views
    686

    So you wanna be a Moldmaker eh? YOU'RE...

    So you wanna be a Moldmaker eh? YOU'RE MAKING A BIG MISTAKE!

    I would say for machines.... Don't make anything yourself. Just wasting you time that you could be making money by making molds....
  22. Replies
    6
    Views
    634

    Did you find a manual yet? I look to see if I...

    Did you find a manual yet? I look to see if I still have one.

    Bill K
  23. Just picked up a EZ Path Lathe need Programming Manual

    Title says it all guys. We need the Programming Manual for a Bridgeport/Romi EZ Path Lathe. We have the install and maintenance manual, and the Electrical manual.

    Is there a download version some...
  24. First thing I would check are the X, Y, and Z...

    First thing I would check are the X, Y, and Z limit switches. See if they are stuck. Next I would check the cables to the limit switches. Not knowing how old your machine is, over time the cable gets...
  25. Replies
    14
    Views
    20,835

    "The lube pump should hold 25 lbs. of preasure...

    "The lube pump should hold 25 lbs. of preasure for a minimum of 3 minutes. If it doesn't, you will get this alarm."

    Yup. No so bogus info

    tjamscad, Did you find your leak yet?
    Should you...
  26. Replies
    14
    Views
    20,835

    The lube pump should hold 25 lbs. of preasure for...

    The lube pump should hold 25 lbs. of preasure for a minimum of 3 minutes. If it doesn't, you will get this alarm.
    Things to look for: Check every inch of all the lubrication tubes. If the preasure...
  27. Replies
    1
    Views
    1,434

    email me. I have what you need Bill K

    email me. I have what you need

    Bill K
  28. Replies
    3
    Views
    1,333

    Have the guy scan your sketch and save it as a...

    Have the guy scan your sketch and save it as a BMP or JPG file. Open that file in Windows Paint. Save it as a Monochrome(black and white) bmp file.
    Open MasterCam. Use the C-Hook ras2vec. That...
  29. Replies
    7
    Views
    1,228

    Okay, Here is my .02... the Haas man is...

    Okay, Here is my .02...
    the Haas man is incorrect. Numbers are numbers + or - a G00 move is a G00 move at what ever Z plane.
    .027 above the part is not enough. We found on our VF-2Ss that we...
  30. Replies
    5
    Views
    865

    GB, I'm with Mark on the feedrate. My best...

    GB,
    I'm with Mark on the feedrate. My best results cutting Lexan, and /or any plastic for that matter, have been with 2 flute HSS endmils and flood coolant. Plastic tends to melt to the flutes so...
Results 1 to 30 of 46
Page 1 of 2 1 2