I'm not sure about a parameter change so I won't comment on that. How is the arm attached to the drive hub, with a taper lock coupling and dowels? It sounds as though maybe the coupling slipped and...
Type: Posts; User: RAC
I'm not sure about a parameter change so I won't comment on that. How is the arm attached to the drive hub, with a taper lock coupling and dowels? It sounds as though maybe the coupling slipped and...
Yeah all of the information for ATC such as what tool is in the spindle and what tool is in the transfer arm or sub arm, is located in a Data table that allows you to reset the info to what is true,...
Give me the whole scenario, i.e. you called the tool, it indexed the magazine, it pulled the tool etc. Where did it end up? Do an M915 to close the ATC door as a start and make sure the door closed...
Ok here's one you may have already looked for, but is this machine optioned with an external scale? I know many of our older 800's were equipped with the scale option. You will be able to see this in...
Ok sorry I didn't realize you had removed it completely. It would be interesting to see what would happen if you opened up the Error Count Parameter that corresponds to the 411 alarm. I can't...
Is there any way you can monitor the load while rotating B axis, it also sounds as if it might be sticking on the Rulon that the table rides on. We usually don't have too many issues with the NC...
Can you tell me if this is a 1 degree table or NC Disc Brake table? It sounds as if the machine believes that B is unclamped when it actually isn't. Does it clear M10 and M11?
411 is an excess...
So it's a 16iMB control, probably built in 05 or so. Have you had issues with it tossing pallets? I'm assuming the pallet doesn't actually fall off but comes disengaged from the drive pins on the...
Is this a Fanuc spindle? If so you might want to have a look at the BZ sensor in the back of the spindle, it sends speed and 1st rotation signals to the drive. As for the clamp issue, can you look at...
What is the serial number on the machine? I am ex Toyoda so I can help you out, we currently have about 100 Toyoda horizontals in the plant, and 630 pallet changers are one of my specialties!;) Give...
Pat at MTW is an excellent guy to deal with, I bought my IH clone from Pat several months ago, and it was a very enjoyable transaction.
Believe it or not, all the big automotive speed shops will carry an oil pressure gauge kit that has the tubing and a variety of fittings that should do the job for you. If you're near The Queensway...
Look for B axis clamp confirmation, you may have lost the clamp signal.
I just tried putting it in 3, and while rotating the spindle I can feel resistance while tugging on the HI handle, but it still won't go. I'm afraid I may have to look at the gearbox. Not something...
I recently bought an IH clone from MTW to get my feet wet and make some stuff. I'm having a bit of an issue getting it into high gear. I've given a pretty good tug on the high gear lever while...
I posted this mistakenly in the General section, so I'm reposting here.
I'm working on a Toyoda HMC with a pair of Sany Denki drives for the magazine and the ATC arm. The one for the magazine has...
I'm working on a Toyoda HMC with a pair of Sany Denki drives for the magazine and the ATC arm. The one for the magazine has come up with a warning that states "the ON/OFF cycles in the Non-Volatile...
The data reload was done after the coolant bath, to try and fix the problem. Upon a little further investigation, it does appear to be a C-language issue, but neither Fanuc nor Toyoda seem to have an...
Hey guys, been lurking here for awhile but his is my first post so bear with me. I'm working on a Toyoda FA630 with a Fanuc 16i-MA control. This control got a coolant bath a little while ago and...
Hey guys, been lurking here for awhile but his is my first post so bear with me. I'm working on a Toyoda FA630 with a Fanuc 16i-MA control. This control got a coolant bath a little while ago and...