584,817 active members*
4,492 visitors online*
Register for free
Login

Search:

Type: Posts; User: Arjand

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Re: Mazak M32 on AJV 25/404N drip feeding stops at same line of code

    anybody got a solution for 887? I noticed this too
  2. Replies
    2
    Views
    1,638

    Re: Cam style program

    You can use Fusion 360 to create the files and offset the toolpath, you will only need (to build) a postprocessor for your control
  3. Re: EMCO Turn 50 Lathe RS485 PC Board Device driver

    Whats your problem?
  4. Re: Alarm 8140 - Maschine (ACIF) not responding EMCO PC MILL 155

    Im pretty sure that your communication cable is not working. So check the 4 wire cable between your control and the machine
  5. Replies
    1
    Views
    2,029

    What do you want to achieve? Very curious. For as...

    What do you want to achieve? Very curious. For as far as I know the only thing you can do from outside is feedhold.

    What I like to do is integrate a probe but a few things I'm missing (on SIemens)...
  6. Replies
    1
    Views
    2,373

    Ever got any further with this? I have ghe same...

    Ever got any further with this? I have ghe same question for my CM105
  7. Replies
    1
    Views
    716

    Re: Instructions Emco PC Turn/Mill 50

    Did you succeed?
  8. Replies
    1
    Views
    3,681

    Re: WinNC Sinumerik 810T position display

    I don't really know. Would like to know. Running a program you see workoffset coordinates, but while joggins its machine coordinates
  9. Replies
    7
    Views
    5,733

    Re: EMCO PC MILL 155 - reliable production mill?

    You can buy regular BT30 holders, but you need the right pull stud. Best chances are to make them yourself.
  10. Re: Any way to get simulation to actually simulate your machine's acceleration?

    No, but you can influence the cycle time calculation on the setup sheet

    Verstuurd vanaf mijn SM-G955F met Tapatalk
  11. Replies
    1
    Views
    1,877

    Re: Concept mill 55 Keyboard problems

    Old topic, but lets try: Is the keyboard made for cam concept? Most keyboards are for Fanuc Siemens or Heidenhain
  12. Thread: WinNC software?

    by Arjand
    Replies
    2
    Views
    2,228

    Re: WinNC software?

    Send me a pm. What is your machine?

    Verstuurd vanaf mijn SM-G955F met Tapatalk
  13. Replies
    4
    Views
    1,121

    Re: HSMExpress to HSM Works

    To get a feeling of 3D toolpaths its better to download a trial of HSMworks. If you are programming more then once a week its worth the effort to invest in HSMWorks. You will get all the simulation...
  14. Re: Any way to get simulation to actually simulate your machine's acceleration?

    You can write a postprocessor to incorporate these times. Take the setup-sheet as a basis. It will take you some time though...
  15. Re: Gap Height between tool and spindle face - EMCO Concept 55 Mill with tool changer

    This is maybe respons to and old thread but maybe usefull for someone. This seems like an old EMCO BT30 holder (for PC mill55/F1) that is used in a concept mill. The concept mill has a different...
  16. Replies
    2
    Views
    2,162

    Re: Fusion 360 Post for HAAS SL20 Lathe

    Yes, I made a commercial post for a customer in the past for this machine. There are indeed diferences. There are for example no radial drilling cycles possible, and some cycles are different. Also...
  17. Replies
    7
    Views
    3,573

    Re: Engraving.. and pulling my hair out!

    Just look out for a single line font and use trace with a chamfer mill with a small tipdiameter.
  18. Replies
    3
    Views
    2,841

    Re: Mazak post for mill turn

    We created a postprocessor for the Integrex that runs very nice, but as I read, that too late now. Good luck with your new machine.



    https://www.youtube.com/watch?v=TBIM-XONU_Q
  19. Replies
    358
    Views
    66,833

    You need ti use hardware interuos. Did you do...

    You need ti use hardware interuos. Did you do that?
  20. Replies
    358
    Views
    66,833

    Re: emco pc mill 50 & similar

    That seams like a ****load of money for an old pc with a card. Is is for a PCmill 50 of 55?
  21. Replies
    4
    Views
    3,561

    You understand that you respond to an old topic?...

    You understand that you respond to an old topic? Maybe there are standard possibilities., there is just an easier way
  22. Replies
    358
    Views
    66,833

    Re: emco pc mill 50 & similar

    I want to try Siermens 840D control on my PCmill 55. It asks for MSD disk that should contain information about the PLCs. I pointed it to different folders like the machine folder and specificly the...
  23. Replies
    1
    Views
    1,140

    Re: Emco pc turn 50 file extensions.

    These are fixed (or not) checkdisk files. I dont think renaming works.
  24. Replies
    2
    Views
    2,304

    Re: EMCO PC Turn 55 Homing

    Not sure if you have an answer. In wincam there is a home button that looks like a bullseye. Click that and it should home.
  25. Thread: Emco Winnc

    by Arjand
    Replies
    2
    Views
    1,713

    You can use Wincamm. Send me a pm

    You can use Wincamm. Send me a pm
  26. Replies
    2
    Views
    3,779

    Re: emco concept 55 mill startup trouble

    True. You dont use the Linux machine. You connect is to a windows machine with wincam/camconcept and that does the machine control. You just found the calculation unit of the machine. In the...
  27. Replies
    358
    Views
    66,833

    Re: emco pc mill 50 & similar

    Wow, really impressive Rich. You can make some money with this circuits als many people would like to have them I suppose! Unfortunately the mill 55 is a bit different, but I'll see what needs to be...
  28. Re: Anyone using HSMWorks Express with Tormach Personal CNC 1100?

    You can drive the 4th axis in hsmworks at the moment, in inventor hsm and fusion 360 you can index the product and mill on a different side, but not simultanious 4th axis. That will follow next year
  29. Replies
    358
    Views
    66,833

    Re: emco pc mill 50 & similar

    Nice find Rich Jones. So I understand you figured out with signals are used on the rs485 cable en reverseengineered you own circuit? Do you think it would be possible to link this with something like...
  30. Replies
    8
    Views
    4,590

    Re: Esprit Training Videos!!

    I have the dvds, but while watching I'm convinced that the effort the maker put in is worth the money. Asking for a copy makes sure that you reduce the chance he will make a new series of video's....
Results 1 to 30 of 43
Page 1 of 2 1 2