504,336 active members
4,146 visitors online
Register for free
Login

Search:

Type: Posts; User: kenrbass

Page 1 of 2 1 2

Search: Search took 0.00 seconds; generated 41 minute(s) ago.

  1. Re: Blue Elephant 6015 woodworking cnc router for wood cutting

    700x1300 would be a better size. A sheet of plywood cut into 1/4 size pieces is 24x48 Having 600 width is not enough to reach all sides of the 1/4 sheet, but 1500 is longer than most would need.
  2. Replies
    1
    Views
    85

    Re: Lagun Swift 4x8 Near Houston for sale

    Sold Sold Sold
  3. Replies
    5
    Views
    41

    Re: Laguna SmartShop 1 Transformer Problem

    your last reply is not logical.
  4. Replies
    5
    Views
    41

    Re: Laguna SmartShop 1 Transformer Problem

    Disconnect the power wires from the drivers and see if it still pops the breaker. Could be a bad driver. If it doesn't trip breaker with all drivers disconnected, connect one at a time and try each...
  5. Replies
    19
    Views
    100

    Re: BOB and NPN Proxy Switch wiring question.

    You could use a relay board like this and from the contacts of the relays, just apply ground to the board input when it's active....
  6. Replies
    1
    Views
    85

    Lagun Swift 4x8 Near Houston for sale

    Laguna Swift CNC Router with 3kw spindle. Table set up for vacuum hold down. 3hp vac pump for the hold down system included. 3hp Dust collector also included. This machine is Running on Mach3 and...
  7. Replies
    1
    Views
    73

    Re: Ezrouter Scorpioin 5x10 cnc router

    SOLD SOLD SOLD
  8. Re: Huanyang VFD and Spindle starts spinning at startup

    It looks like you have a wire plugged into the fwd terminal. Try taking that off
  9. Replies
    1
    Views
    73

    Ezrouter Scorpioin 5x10 cnc router

    2010 Ez router Scorpion in great running condition. 5x10 cutting ability and an ATC tool changing spindle. The spindle is set up as semi-automatic tool changing. New Centroid Acorn controller running...
  10. Thread: ShopSabre

    by kenrbass
    Replies
    4
    Views
    74

    Re: ShopSabre

    I don't think it will, but you can ask the folks at wincnc that make the controller for them. Kelly or Mike over there are good people. It's not so much a shopsabre question but more of a wincnc...
  11. Replies
    3
    Views
    69

    Re: WTB ShopSabre 23

    I tried to pm you but it doesn't work. May be your settings.
  12. Replies
    3
    Views
    69

    Re: WTB ShopSabre 23

    I am going to sell a 48x48 cncrp machine soon. SW side of houston.
  13. Replies
    4
    Views
    83

    Re: Chinese CNC Retrofit G540

    The first thought that comes to mind is that a 24 volt power supply seems very small. What power supply did it come with originally?
  14. Replies
    3
    Views
    127

    Re: with DM860A stepper driver

    If your motors (klunk) and lock in to where they can't be moved when powered up, your motors and drives are probably good. If you post what kind of board you bought and the wiring diagram with some...
  15. Thread: 5 Axis

    by kenrbass
    Replies
    4
    Views
    114

    Re: 5 Axis

    I don't think they have a machine with enough Z clearance for a 5th axis. If you call them, Brandon is very helpful. I have a different machine now with rack instead of ball screws and it cuts as...
  16. Replies
    2
    Views
    63

    Re: Chinese Spindle Upgrade

    I used to own a shopsabre, but have a camaster now. Anyway, I have a 1.7kw spindle and vfd that I pulled from it. I am going with an ATC spindle and rewiring for that. If you want a good used hsd...
  17. Replies
    0
    Views
    914

    Re: Configuring Z Axis Touch Plate

    m5
    (Is plate under bit ?)
    G4
    l210z
    L91 G1 z-10 m28 g31 f20
    L91 g1 z.2
    L91 G1 z-3 M28 G31 f5
    l212
    g92 z .125 (plate thickness)
    l91 g0 z5
  18. Re: Used 4896 ShopSabre with No Controller - In a Quandary - Please Help!!

    Where are you located? Wincnc is a great controller. I have an older 4896 shopsabre also. I think wincnc has an agreement with shopsabre that all controllers and parts go through shopsabre for new...
  19. Replies
    2
    Views
    32

    Re: Dust Collection

    Join in here and maybe you will get more input. I re-did my machine to have top loading tools and made my own smaller skirt. Aluminum should be a touch heavier than sawdust, so I don't see why a...
  20. Re: Touch pad for setting z-zero on a 4896ATC?

    I bought mine direct from wincnc which is the operating system guys. If you need help and support, you may be better off getting one from shopsabre. I wouldn't go without it.
  21. Shopbot Benchtop 2007 24x32 cutting area 6 inch z height

    It is made by shopbot dated 2007. Everything is functional and works fine. It had something fall on the controller and wrinkled the skin on the tower that controls the machine, but that does not...
  22. Replies
    22
    Views
    1,542

    A more important aspect of this for me would be...

    A more important aspect of this for me would be having a vac table routine between sheets.
    After you unload the parts from the table there is always some dust left behind. Having a routine to start...
  23. Replies
    22
    Views
    1,542

    If the parts are the same, just nest as many as...

    If the parts are the same, just nest as many as will fit on one sheet and run that same file 5 times.

    You should have a repeat file button on your machine.

    You still have to clear the parts and...
  24. Replies
    7
    Views
    61

    Here is the new wincnc screen that I built for it.

    Here is the new wincnc screen that I built for it.
  25. Replies
    4
    Views
    226

    Have you tried using the flat area clearance...

    Have you tried using the flat area clearance tool? It's not quite what you are asking for, but I might would help.

    If visualmill would do it, I have a copy collecting dust.
Results 1 to 25 of 37
Page 1 of 2 1 2