G00 x 4.284 y -.525
G03 x 4.284 y .525 I -4.284 j -.525
The radius to be cut is on center x and y. I am cutting a counterclockwise direction. I am .525 from each side of part that is being cut...
Type: Posts; User: larry53
G00 x 4.284 y -.525
G03 x 4.284 y .525 I -4.284 j -.525
The radius to be cut is on center x and y. I am cutting a counterclockwise direction. I am .525 from each side of part that is being cut...
I am still having problems. I guess I can not take a segment of a radius and use G03 to cut the part. The G90 did help make the arc but it is not centered with the part. It is cutting more on one...
Since I posted this I learned that this controller defaults to G91 , incremental mode. I had to stop and do other things but think if I add a G 90 at the beginning of the program might solve some...
I added to the pdf drawing
The Controller is made by Microkinetics. it is a MN400 multi axis contouring motion controller. Thanks for any help. Larry
It was easier to mount in vice the way it is shown.
I need some help on programming to cut a simple radius on a part. Having problems getting the correct radius on the part. I have attached a pdf and hope it has enough detail for someone to give me...
The part to be machined is approx. 7 inches x 3 inches. The mill tool start is at zero position, the starting position is at 0 x, 0 y, .050 z. When the cam program changes to g codes and m codes...
I need some help on saving an .dxf file for use in a cnc mill. Do I need to set the UCS to zero before I send it to a cam package? I sent one to a cam package and converted to g codes and m codes and...
What is the material used on these parts?
I am located in Fayetteville, N.C. Send me contact information and I will send a quote on your parts. Thanks Larry
Just so you know. 416 stainless is not a good stainless steel to weld. It is subject to rust. 304 or 316 would be a better choice of stainless steel
You need to add the length of the part and the material.
I am trying to get my laptop to accept a wireless internet connection. The laptop has wifi. I currently have time warner modem model sbv5222 for my desktop. I have purchase a router brand name...
Is the file you sent in inches and 1 to 1 scale? Not sure of the dimensions I am getting are correct.
If I save a file in a pdf, using .Pdf reader program can the document rights be enabled or do I need a .pdf writer program to do this.
Thanks.
Would that be the file propertys in the AutoCad file?
I am to be losing a lot of detail when I save a file from a Inventor .idw file into a AutoCad .dwg file. The AutoCad file can not be edit, its only a read only file.
There is also no color fill in...
I may be wrong but I thought there was a way to add a knurled surface to a part. It seems like it was at the same place where you could pick bevel surface. It was at a pull down menu. Maybe I was...
I found a error in the drawing. It is fine now. thanks for the input.
I am having trouble with I extrude a hole or center point in a model. It leaves a what appears to be a strip in the middle. I have tried several things but no matter what I have tried there is always...
I agree that this computer can not be increased no more than 4 gig from the expert,honest answers to my questions on the forum. Believe me I even ask HP if a 32 bit can be increased to 8 gig. Guess...
I have done a fresh install. As for the reason of adding more memory to this computer which can not accept more memory. Again HP said to me after 4 hours on the phone that this computer can go to 8...
I am not that good on changing any settings on the computer. The memory upgrade site does not show my model. The only information I have that this computer will go up to 8 gig and should accepted and...
Yes it is a 32 bit system, however this machine was special ordered from HP. According to HP this machine is set to go to max of 8 gig.
I click on my computer, then properites.
The bios setup listed as follows: Installed memory 5120/pc2-5300
Memory banks, 1thruough 3 has 1024mb/DDR2 Sdram, bank 4 has 2048mb/DDR2 Sdram. I already had the bios updated by direction of H.P.
I have a H.P. desktop computer that was made in 2006. It is suppose to be able to go to 8 gig. I have contacted H.P. and they also said it could go to 8 gig on the ram. It had 2 gig and I added...
That is what I thought. I had them walk me through and set my Outlook to their email address. I guess my old email will end at the end of the month. I guess some people would say anything to get out...