SOLD
Type: Posts; User: wmgeorge
Sold pending funds
Can you replace that bolt with a allen head bolt of some type and have you contacted Avid / CNC Router parts?
$50 plus shipping cost and PayPal is fine.
$60 plus shipping cost. cheapest way and PayPal is ok
PRICE DROP $75 Shipped Lower 48
PRICE DROP $65 Shipped lower 48.
Made for CNC Router Parts - Avid automatic surface and corner setting with their controller and panels. I paid $130 for this plus shipping and sold the machine. Works perfectly with Mach4 and their...
CraftyCNC touch probe for digitizing with Mach3 and other software but not Mach4. Purchased and used once with Mach3 and also with the software he sells but now using Mach4 and the vendor has no...
You would be far far better Not using the Parallel port. I have a Windows 10 computer I keep off the internet for my CNC control computer.
I am confused a picture shows nothing useful. What is the part number and brand of your control box and what control software are you using now?? I suggest going to the Newfangled solutions website...
Mach3 has little quirks. Others will say not :):) , switch over to Mach4 and I am assuming your using Warp9 ESS.
I have the PMDX 416 running on Windows 10 USB. Sounds like it might be your computer. Mine is a Intel NUC the very basic one and older with a VGA out. Has 4 USB ports, and runs this CNC which is a...
Tah da... took my Verizon cell phone to the shop and tried what I tried yesterday made it a Hotspot and connected my shop computer thru it. Ding ding, worked like a champ now so I got my Mach4...
I am unable to access the website with either MediaCom cable or Verizon Wireless, oops just got on with my cell phone or Verizon network. Its still timing out on the cable connection, before I...
I have all my limits and homing on the same pin and it works fine. All my switches are NC and wired in series. When the Homing sequence is started, Z goes to the top and hits the switch and backs...
What I learned you can not have a A motor as Slave to your X. Your motors are setup with Motor 0, Motor 1 and so on and then assigned to the axis. Take A motor out all together. Then whatever motor ...
Same thing Mach3 has some issues and some on here will argue that point, but going to Mach4 (and both ran Warp9 ESS ) solved those minor unexplained glitches .
Been trying to get a license activated and can not get on the website or support website since yesterday. Did a tracert and it ended up not at the correct site and timed out??? Never issues in...
If your using Warp9 ESS there are complete instructions for it all online.
If your running on the parallel port do yourself a big favor and switch to Warp9 ESS or I am running now PMDX USB card. I think your getting RFI or EMI causing glitches in your running program.
Joe I will be 77 next month and I just sold my 4x4 FLA machine, it was too large for me to mess with and I had a mild stroke this January so it went to a good home. I have converted a few machines in...
Looks pretty straightforward, after all a bi polar stepper is just 4 wires all you need is an ohm meter to pick out the two winding's and A or B + or - is just change any two wire around until it...
Biggest mistake using a control board and software no one else uses and that equals zero support.
Its a hobby, if you tried to hold +/- .004 in a real wood shop you would be out of a job.
Thats .0039 or .004 inch which is the thickness of a sheet of paper, that is why they make clamps and glue. If its metal to metal then the bolts holding the two pieces together should draw that...
So you really need a milling machine and a water tight metal or whatever material your using without a gasket? I have been in and around machine shops most of my 76 years.
I am wondering what your making out of wood that requires it to be more accurate than 1/10 of one mm? Wood expands and contracts more than that! Yes put on a spoil board.
SOLD......
Back up for sale non paying buyer so its re-listed, Make me an offer in cash . no trades, no checks.