Search:

487400

Wondering if the DATA IN/OUT->INPUT command or the FOPENA->READ>GET command is available in auto mode running a .min file

output of parameters from the machine in the attachment

https://youtu.be/rYqzJM3Dk0s

it is by design so the material doesn't roll upwards from under tool into the end of the mill, rather the material is only introduced on the side of the endmill thus creating more desirable and easy...

487370487372487374

487356487358487360487362487364487366487368

This was my mistake the code shown here was cut together because it wasn't the first instruction after toolchang in the CAM sequence. The correct M code there is M16
Also here is a picture with the...

Hey Guys!

Okuma Genos M560R-V +4th axis (Tsudakoma RNE 200 R,D integrated solenoid operated pneumatic brake, simultaneous 4axis capable configuration )
Okuma Genos M560V-e +4th axis (Tsudakoma...

Totally agree.
Thanx for the extension.
I'll try the displacement measuring methood too next time I get in to some mission critical tension stuff ;)

In the end it turned out the problem was in the spindle belt slippage. The belts were worn out so they slipped even at proper tension

To my knowledge it is simmilar build to the european version (esv4020 by the label, EurocenterV50). On those machines there is a fine sprout gear like piece on the spindle near to the v-belt section....

I'm so happy that i found You but since You are not pushing the issue forward, pleas leave this post before i delete it.

If i would use inverse time feed than a single line with 200 feedrate...

I can not fizzle with the machine for now but i can include a part that contains the debug information

I am aware that i can roughen up the toolpath a bit an get rid of the micro angles but still...

My main concern is the behaviour of the machine, the code is ok and the feed is ok, I'm working on the problem for two months by now, so please answer the machine related problem, this is not a...

In the post to make my self sure in the debug part i made a calculation with the inverse time equation too and it gives the same values not to mention the manual paperform calculations which gave the...

Machines known for this problem:
Okuma LB3000 EX II-MY C950
Okuma LB3000 EX II M C1000 with SMW SLUX-2 snug on steady rest
Okuma Genos M560R-V with...

Hello guys!
The machine: Okuma Eurocenter v50 (ESV4020) / Osp u10m
Made in Czeh Republic around 2002 (Electrical drawing number E-777/778)

A few days ago a colleague noticed that the spindle of...

1.: I have no idea of where the effective zone was set up originally by Okuma tech (builders), but hopefully that is okay.(we can close this out as We already know that the error happened at near the...

Hi Guys!

Today morning I have encountered the error described in the title. The machine Z axis was left nearly at the halfway of its travel length before powering down yesterday in the evening. I...

In the end I should say "not every signal is a signal". Optical sensor feedback on sensor body looked ok, on th distributor panel too, but the sensor was failing in voltage I think so MC was missing...

Hi guys!

I need help ASAP! I have the error described in the title.
I can put tools back in to magazine from spindle without problem
I can call another tool when tool is in spindle (toolchange...

Thanks to booth of You for the infos: I have been strengthened in my toughs.

To answer Your question: My Fanuc machines are 2 year old at this moment, they have been bought from the local brand...

Hail Guys!

In the near past, My experience has grown a lot in intelligent roughing techniques. By the way I have started to face the high table feedrate related problems such as clattering in high...

In the finish We've discovered that KA110 and KA111 relays were failing on the winding change so We've replaced them with 2 new one and voila MC is ready to fly.... error searching method: when the...

In the finish We've discovered that KA110 and KA111 relays were failing on the winding change so We've replaced them with 2 new one and voila MC is ready to fly.... error searching method: when the...

Omg!!! Our employee forgot to wipe tool number from the tool lists actual tool row and removed the tool from the spindle manually by hand and that was the reason for not being able to spin up the...

I've repaired the motor but the problem still exists:
Problem MA-400HA ALARM 1151-02 ALARM-A #13 - Page 2 - CNCzone.com-The Largest Machinist Community on the net!

I've disconnected the motor from the drive unit (inverter) at the box on the motor and did the measures after, and discovered that the wiring was in contact with the upper (fan side) bell of the...

we measured and it seems we have some phases leaking to the frame again...
Can the failure of the speed range shift relays cause the winding to melt down in the motor?? We are up to disassembel the...