Search:

I have a Sinjoe with an AWC708C Plus. I had been running it off LaserCad 7.66 but had to get some computer work done and had to re download LaserCad. Now, after re downloading 7.66, 7.88 AND 7.95 I...

yes. i have heard that before and even tried it out. its learning a new software and cam and trying to figure out if its worth the time and the anxiety that not knowing how it will go will create...

you are a reseller?? pm me if you have prices that would be lower than mecsoft/rhino

I have a JCUT CNC Router that I use for carving wood helmets. Deep Z and compound curves. Its a pretty small business operation. Not my main source of income by any means

I used to have Rhino...

will do later today. :)

Thanks again! and again!

I am up and running. And a little wiser, if quite a bit behind!

HE1957 Your help made a HUGE difference. I can't say that enough.

THANK YOU! He1957
I got a new file from the manufacturer and using your last procedure numbered 1-4 I was able to get the update onto the DSP. At first it wouldn't load but then I played around...

Ok. Back at it this morning.

RichAuto Facebook got back to me. They won't help me since I didn't buy the DSP directly from them.

I sent an email to you AllenCNC at the omnisales address,...

I am sending you an email. I saw the instructions and when I choose "view version..." it say the update version is: P1.1038 - not sure what to do with that

Ok. So, when I start the DSP with my computer, holding down two buttons on the DSP, I cannot get it to go into "flash disk mode" and even though i have powered the dsp up with the pc the pc doesn't...

ok. so i have tried to update from two different usb's and from my computer (no luck). Both times when I downloaded the pkg file from the richauto site to the usb i got the "file is cracked or...

I downloaded the pkg file to the usb and used the emergency operation and was able to see the predicted displays in the emergency pdf you linked. I tried to upload the update pkg file but got a...

Ok. So, I did not know about the various cables, data only and power capable. I found another USB cable and it was able to power up the DSP direct from my PC. However, I still only got the same...

Thanks. No USB port worked to turn it on.
Regarding step 3 and further, when I turn on the DSP using the CNC Machine power it simply says "RichAuto system is loading..." and nothing else happens. ...

Should I connect the PC to the DSP while the CNC machine is on and attached to the DSP? This is the only way I am able to turn the DSP on currently

So, shortly after I got this last message the DSP loaded up again. Since then I have been keeping it "on" so that I don't lose it. Recently I had to turn it off and now it is not loading again and...

Ok :(
So I went to the store to get a new USB (I don't know how to clean or "uncorrupt" the old one) and loaded the gcode files from my computer hard drive (not from the old USB) on it.

Then,...

alright. first one. at least so far. i took the usb out and it did the same thing. then cycled it through another off/on and it loaded. so, fingers crossed, it was just a corrupted usb. will...

ok. thanks for the detail. will try it out and see what happens. if i get to the firmware reload i will be in above my head a bit and may ask for some more assistance. thanks again!

I have a j cut dual spindle wood router. It has a rich Auto a15s controller. When I turn it on lately the display reads Rich Auto is loading and then nothing else happens. See pictures. Anyone has...

Thanks guys. I rewrote the lines and will try them tomorrow. The model/drawing seems good and simulates just fine so if that is the problem I will need to dig into that further that my current...

yes. i see what you are saying MacTec. the Z values in the lines are absolute values and not relative/incremental (could this be the problem?). if i had posted the entirety of the lines you would...

i do not know since that line isn't in the file. should i write it in? if so, where?
in the past the fanuc post processor did not generate a g91 command with rhino cam 1.0. i am using fusion 360...

Hello. I am having to switch my CAM from Rhino 1.0 to Fusion 360 after 5 years using rhino with my JCUT Router (with a handheld controller). I originally used a Fanuc type post processor from the...

G01 only makes X and Y move. G00 makes XYZ move. Z will not move with G01.

I am novice enough that I don't know what the generic post processors are called. There are several dozen to choose from. Can you let me know an example?

And, yes, the machine does move/jog in...

Hello, I am a novice with CAM and gcodes. I am trying out Fusion 360 for my Chinese JCUT wood router and created my first test 3D pocketing post (Fanuc). Previously I had used Rhino Cam and I...

Thanks gfacer and everyone else. Like I said the machine has been working fine as I have just left it on and, magically, the problem went away after it "warmed up?". In any case, yesterday I pulled...

Thanks so much, I will try this out and let you know what happens. Right now I am just leaving the machine in the "on" state to avoid dealing with this issue until I have more time.

Is there any way to more specifically diagnose it as a controller issue before I buy one and swap it out?