509,973 active members
3,228 visitors online
Register for free
Login

Search:

Type: Posts; User: mbservice

Page 1 of 16 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    36

    Re: Help needed - Fanuc Programs backup

    It depends what control you are on
  2. Replies
    1
    Views
    18

    Re: Alpha Harrison graphics board

    Can you post the number off your board ?
    What makes you think it's the card ? Are you sure it's not the CRT
  3. Replies
    2
    Views
    112

    Re: Hitachi seiki ht20sii problems

    Do you have a back up of the machines original parameters
  4. Re: Citizen 1999 L432 Meldas 500L error messages?

    Where are you I think I decommissioned that machine
  5. Replies
    4
    Views
    50

    Re: Bad finishing issues

    Check your backlash that tool is jumping possibly due to x and z axis not moving correctly or as previous poster said use at least 1mm finish cut to push the job
  6. Replies
    4
    Views
    1,109

    Re: Conquest 42 turret problem

    If the procedure doesn't work or if the turret is still sitting 1/4" out like you said you may have a mechanical restriction stopping it sitting on the coupling
  7. Replies
    1
    Views
    28

    Re: Bridgeport Interact 1 TNC145

    Check your motor brushes
  8. Re: Fanuc OM 086 p/s Alarm RS232 Parameter

    What card reader are you using
  9. Replies
    66
    Views
    2,468

    Re: thank u sir

    Check your 24V
  10. Re: Colchester Tornado 220M Fanuc 21iT Turret Reference

    Messaged you
  11. Replies
    1
    Views
    41

    Re: Lathe Alpha 400 macro program

    Hiya
    What version 400
    Please private message me as don't always get notifications
  12. Replies
    2
    Views
    34

    That option may not have been turned on

    That option may not have been turned on
  13. What did it stop on? Tried to message you direct...

    What did it stop on?
    Tried to message you direct but won't allow it
  14. Thread: Help

    by mbservice
    Replies
    1
    Views
    133

    Have you had a look at the YouTube video

    Have you had a look at the YouTube video
  15. Replies
    4
    Views
    103

    Id put a clock on the bearing and see if any play...

    Id put a clock on the bearing and see if any play
    Sorry only just seen your reply easiest thing is to private message me
  16. Replies
    6
    Views
    491

    Hola son las conexiones iguales ¿Hay luces o...

    Hola
    son las conexiones iguales
    ¿Hay luces o voltajes en el tablero?
  17. Thread: Mitsubishi

    by mbservice
    Replies
    3
    Views
    147

    Have you checked your tool settings page ? They...

    Have you checked your tool settings page ?
    They may be switched off in there

    Do you have tool life monitoring turned on ?
  18. How are ok generating your programs ? On machine...

    How are ok generating your programs ? On machine or on cam system
  19. Replies
    1
    Views
    36

    Have you checked the parameters for the 5th axis ?

    Have you checked the parameters for the 5th axis ?
  20. What machine is it ?

    What machine is it ?
  21. I'd clear all and reload where abouts are you ?...

    I'd clear all and reload where abouts are you ?
    Please pm me for instructions how to reload
  22. Replies
    0
    Views
    156

    Check your drives

    Check your drives
  23. What control is on the Tornado ? For them you...

    What control is on the Tornado ?
    For them you don't use 1815
    If you send me your email I'll send you a procedure
  24. If you changed the batteries when the power was...

    If you changed the batteries when the power was up there is a high probability that you have contaminated or lost your parameters and require reload
  25. Hi Even though you have changes the battery the...

    Hi
    Even though you have changes the battery the turret still requires referencing
    If you send me your email I will send you the procedure
Results 1 to 25 of 377
Page 1 of 16 1 2 3 4