If your the machine builder. I assume you can access the plc: using tncremo. I believe parameters are there. But on our machine we needed a password to access even through tncremo. So the machine...
Type: Posts; User: pinguS
If your the machine builder. I assume you can access the plc: using tncremo. I believe parameters are there. But on our machine we needed a password to access even through tncremo. So the machine...
I will have to check our manual which version required the use of plane spacial, which i can do tomorrow. Regarding the password, this will be with your machine manufacturer who may be reluctant to...
Yes we had to change mp7500 after getting parameter password. You may need to do the same
Hi.
We already had FCL 3 on the machine. However the lock axis alarm i am assuming you parameters havent been setup to allow 5 axis. We do not use Cycle 19 but program with plane spacial.
I can...
Cool, well, if still no luck, no harm in taking a look at the Solidcam File here either.
Check you clearance / plane heights. May be the problem. It should start to feed before it hits material. Likely your starting actually in the material. Also if say your milling out a depth of 3mm...
Have a look at your machine file, depending on Solidcam version. You probably got it limited in there. And if your setting up higher, then it can alarm out.
Are you doing the simulation to take all that material in one cut? Looks at though the cut length is not long enough on the too setup to take all that material. Ideally you should clone a real tool...
Have you tried setting the cut tolerance down lower, whats it at the moment. I have a habbit of doing it at 0.001 - 0.002mm
Hi all
Been a long time, just wondering has anyone used any of the new features in 2013, i.e. Multiaxis Blade or Port etc etc. Deciding whether to get this option, or whether its a glorified HSS...
Also there is a parameter I believe in the 900 series which turns on the 4th axis controls, PM me if you get stuck, I may be able to help.
Hi
The amplifier we used was
A06B-6079-H103
Picture attached, also the other picture shows how it has been connected, the green wire goes to the Cincinatti Rotary Table which we have. After this...
Hi all
Just wondering, in the machine file, I have specified the machine has a chip conveyor. Option set to ON/OFF
How do you select this option when programming, and what part of the GPP file...
Hi
Yes the cooling system is running through fine and holding at a temperature of about 20 to 30 deg on the cooling unit. All flowing.
Where should I check the power consumption of the C axis,...
Hi
All, just wondering if any of you have ever had this alarm?
25 Drives Temperature Max
It occasionally occurs, and I believe I have seen it, on the larger movements on the Y axis.
Its a...
Damn this upload
Its should be here now
I have attached the file I have been working on, it seems all there, I think.
It is the last operation I am looking to at. This one is my latest attempt and seems to be right, but just wondering...
Hi all
Just wondering, where do you change settings so that when you use host cad simulation and look at the data, it actually shows the A and C values, instead of constantly being 0 ??
Ok I am trying to extract the Solidcam File, but the size is massive, i've tried deleting stuff from the zip file, but not sure which ones to keep, what section should I post. Would just the...
Hi
When you say split line, would this be length ways across the middle or the shorter distance and cut the face into 2?
Hi I have attached a PDF of where I am trying to machine, it inside the hole at the top, its just a chamfer, which I'm trying to use a lollipop cutter to do, at the bend intersection.
But...
Hi all
Just wondering, when you use 5 axis machining, how do you set the entry point to be inside of a hole, let me explain.
If you have a bent elbow lets say, i.e. a copper 90 deg pipe, and...
Dont worry, worked it out
Right click on operations and then select cam tree view
Hi all
does anyone know how to display the operation number and tool in the tree to the left
On one of my parts it has the operation number and tooling in brackets
i.e.
HSR_r....T16(1)...
It is strange, we're on a full maintenance licence, and we have only had a machine simulation setup just under 2 weeks ago, so can be expired.
Nope, they're blanked out, strange hey
Hi
Not sure what planet I was on, but the ramping stuff is under link tab. Stupid me, anyway, just for a quick reference, if I have various holes, some small and some upto 25mm diameter, and I...
Hi
I normally set to external to guarantee it cuts from clear area, if I set to internal using the cylindrical profile, is there a way to increase the minimum helical ramping radius? Because if...
Hi all
Just wondering, not sure what I have done, but suddenly my stock is not visible in the machine simulation? To be honest, never really checked if it was before, but either way, it has...