Hello, I tried to PM you but didnt work. I also have a fanuc Om C, I believe. I was wondering if you could help me confirm that. And I'd be interested how you set up your probe and tool setter? ...
Type: Posts; User: Fabric8r
Hello, I tried to PM you but didnt work. I also have a fanuc Om C, I believe. I was wondering if you could help me confirm that. And I'd be interested how you set up your probe and tool setter? ...
Finally got around to working on the machine again. thought id post an update. Hope it helps someone out in the future. I changed out the Pressure switch in the bottom Picture, and put a New F.R.L....
There should be a Brake switch on the back of the control panel. Turn that switch on and hit the reset button. This should release the brake on the tool change motor. then you can manually move the...
Ok. I Finally got back to this tool changer problem. I have noticed after more playing around. That it seems to be air pressure causing the problem. I would not have thought about this. Thanks...
Ok, I made a coupler to attach to the cam box drive sprocket. It seems to turn over fine. No binding, and there is not much play or wiggle in any area of the travel. the most play i get is when the S...
The chain that connects the electric drive motor to the cam box. i would call it the drive chain. Also how hard should it be to turn the motor over? like i said its pretty tight to just turn the...
Thanks. I also removed the chain from the motor to the gear/cam box. The motor is tight to turn by itself. is this normal or should it spin pretty freely? I will get the chain back on and turn it...
Thank you Darryl for all your help on these machines in this Forum!!!! I have read many posts you have helped with. Do you know if there is any place i can get the books and manuals for this machine....
I have not specifically tried this. But with all i have done to it so far. I cant say i have felt any free play? I can try it out as soon as i get out there again.
Hello. I have a Tool changer issue on my Daewoo ace v50. Side mount tool changer. The machine is new to me. But sat for quite a while before i got it going again.
My trouble is the tool changer...
Im hoping ill have this 10pin edge connector figured out by next week. I have found out this Prototrak CRT monitor runs at 15kHz, it needs to have the signal doubled to atleast 30Khz or the new Lcd...
I bought the above Lilliput 8" monitor. to replace the CRT in my Prototrag A.G.E. 2 control. Mine also has the flat 10 pin edge connector. Can anyone tell me how the video connections might work? I...
Hello, I sent you a PM. let me know if you recieve it.
Thanks, Scott
Hello Looking to see if anyone has OneCnc lathe for sale. just picked up a cnc lathe now searching for some software.
Thanks, Scott
Thank you for the info I checked into it and I told them you refered me. But I dont think this is the rout im going to go. The upgrade is 7,500. Thats not Affordable to me. It seems like a nice...
Hello Im having a brain fart. What mesurment on a screw do you look for to Have .100 movent in 1 revolution. Is this the pitch? or is it threads per inch. When Im looking for ballscrews all I see it...
Hello I was wondering if anyone would now if I bought Scales with round connetors on them for a mitutoyo DRO if I could cut the connectors off and put on DB-9 connectors for an acu-rite DRO, their...
Hello I have a couple of magnetic contacters in a lathe. My question is is there a way to test to see if a coil inside the contactor is good. I accidentaly hooked up a wire wrong and had a puff of...
Hello I would like to lern more about how electonics work that is my weekness. I want to get into building my own cnc controlls and beable to trouble shoot my own machines when they go down. In...
Could someone please explain to me how these work a diagram would be nice if you could.
This is my idea I'm not sure if im right or not. It has a low votage to suck it in then it connects and lets...
Hello I have a bridgeport mill right now that uses an older anilam series M controller. I just had a technician out the other day to look at my mill. He said my controller is dated which I new. But...
Thank you so much for the information. is there an easy way to tell if my motors have encoders on them. from the discription on them it looks like they have tach's on them do I have to remove these....
How do I now what amp The tranformer has to be. does this have to be as big or bigger than my continues amps on the motor. So I would like to have around 6-7Amps and if im using 3 of these motors...
In another thread I was told I should use 170Vdc powersupply to drive my motors. I was thinking of going with the Rutex 2020 drives there rated at 200V/40Amp does this sound like they will work. ...
Thank you guys for your information its looking good. I was looking at using 3 Rutex 2020 drives they are rated at 200V/40Amp. Does this sound like a good choice. Im still a little confused as to how...
All, Thank you for the input and info its greatly appreciated. I wasn't clear on my last question though. I was wondering how you came up with the 160-180 VDC as the required volts for this servo...
How do you get the 160-180 Volts.
T%hank you, Scott
This may be a stupid question but im not very good with this stuff yet. Im trying to figure out a power supply size. and im wondering what Volts and amps Im supposto use to calculate this. Here are...
Hello Im kinda new at this stuff and am having a little trouble. Could you please help me out. I would like to understand how to choose the right drive for my motors or any other motors. I saw this...
This is the specks on the motor I have.
SEM small electric motor, perm magnet DC servo motor
Cont stall torque 3NM Tenv
Max rpm 2400 Volts 142 Pulse amps 30
Tacho 9.5 ...