584,842 active members*
4,523 visitors online*
Register for free
Login

Search:

Type: Posts; User: NetStorm

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    667

    I'm trying to do it on a breadboard. It seems one...

    I'm trying to do it on a breadboard. It seems one end goes to gnd, the other to the out put and the other to vs but there should be 4 ends not 3?

    I hope this make sense.


    Sent from my iPad...
  2. Replies
    3
    Views
    667

    Soldering diodes

    Could someone please show me how I am supposed to wire the diodes in this schematic. I am completely new to electronics and I just don't get how this diode is supposed to join the others.

    An...
  3. Replies
    2
    Views
    1,087

    It is a custom format, it prints to file, that...

    It is a custom format, it prints to file, that file then gets loaded to our machines which can understand it.

    A HPGL format wont work as I need to enter the settings in the picture above.
  4. Replies
    2
    Views
    1,087

    Custom Plot file

    I am hoping someone could help me.

    We have some old machines that use custom software, we currently draw in Turbocad for DOS, save the file as a plot and our machines read it nicely.

    However!...
  5. Replies
    0
    Views
    2,978

    Plotter Driver problem

    I am hoping someone could help me.

    We have some old machines that use custom software, we currently draw in Turbocad for DOS, save the file as a plot and our machines read it nicely.

    However!...
  6. Replies
    1
    Views
    390

    CNC out by a few millimetre

    Hopefully this is the right section of the forum to post the below question.

    I have a Torchmate CNC which we use with a router for cutting polystyrene foam.

    I set the start position at 0 and...
  7. Replies
    3
    Views
    1,044

    Revamp Existing Machine

    Hey,

    I hope someone here could help me out. We have an existing industrial size hot wire cutting machine which was custom built some years ago. The guy that made it is no longer around and the...
  8. Replies
    5
    Views
    1,441

    Thanks for all the comments, I would really...

    Thanks for all the comments, I would really appreciate it if you could send me the video to [email protected]


    Thanks once again.
  9. Replies
    5
    Views
    1,441

    If I Use spot drill my controller returns this...

    If I Use spot drill my controller returns this error for every point...


    "A move has been specified but no motion mode (G00, G01, G02, or G03) has been indicated"

    Thanks once again.
  10. Replies
    5
    Views
    1,441

    Drill Multiple Holes - Newbie Question

    Hello again,

    I have another question for everyone out there which I am struggling to find an answer.

    I have a 4mm drill bit attached to my router and I want to drill 8192 4mm holes in an 8ft X...
  11. Replies
    9
    Views
    2,017

    Thanks for all the help guys I think I am getting...

    Thanks for all the help guys I think I am getting there now. In my drawing I have offset by the radius of my tool and used those lines as my toolpath. I have not yet run this on the machine as the...
  12. Replies
    9
    Views
    2,017

    My First Wooden Cut

    Hello,

    I am very new to the world of CNC, I have been drawing for a few weeks now and been cutting some polystyrene foam with my router for a few days which has been working quite well.
    ...
  13. Thread: scale drawing

    by NetStorm
    Replies
    4
    Views
    1,677

    Toby, How would you scale down and make the...

    Toby, How would you scale down and make the drawing smaller? The scale box does not allow a minus symbol.
  14. Thread: Beginner

    by NetStorm
    Replies
    3
    Views
    1,097

    Thanks

    Thanks
  15. Thread: Beginner

    by NetStorm
    Replies
    3
    Views
    1,097

    Beginner

    Hello everyone,

    The company I work for is purchasing a new CNC router. it has been ordered and will arrive within the month. No one here has ever used CAD/CAM software before so we have a bit of a...
Results 1 to 15 of 15