584,866 active members*
5,003 visitors online*
Register for free
Login

Search:

Type: Posts; User: etech4u

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    1,225

    Re: LUCY!!! Need software updates

    Do you have her Email address. I have not spoke to her in over a year so I have misplaced her contact information.
  2. Replies
    15
    Views
    4,172

    Re: MPC6515 and LacerCut 5.3

    I am having the same issue. I have a G. Weike LC1290 and just installed the Lasercut 5.3. My old computer died so I bought a new one with windows 8 on it. I am hoping that someone has figured...
  3. Replies
    4
    Views
    1,225

    LUCY!!! Need software updates

    Lucy,
    This is Brandon, I bought two of the LC1290 laser machines from you last year. My windows XP computer just died and I need the drivers to run this on a windows 8 computer. I see you have...
  4. Mastercam CNC Programmer Needed!!! HAAS Machines

    We are located in Ann Arbor Mi. Currently have 4 CNC programmer positions open both day shift and night shift. Must have Mastercam X or newer experience. We are primarily a Prototype shop so a...
  5. Yes I own two of the LC1290 machines and they are...

    Yes I own two of the LC1290 machines and they are great little machines. I have not really had any issues with them at all. A few minor adjustments and I was off and running. Lucy was my sales...
  6. You were correct, that is all it was. All is...

    You were correct, that is all it was. All is good now. Thank you!!!
  7. Steve, I do not work for Gwekie but I did just...

    Steve,
    I do not work for Gwekie but I did just purchase the 1290 that they sell. I bought just about every accessory they offered two different 4 axis rotary units, large chiller unit, lens, auto...
  8. It does go to the zero origin point when I turn...

    It does go to the zero origin point when I turn it on. It just goes all the way across the table in x or y when you hit the arrows. The worst one is the z neg direction because it over travels and...
  9. Replies
    0
    Views
    1,146

    Setup Geweike 1290

    Does anyone have a decent manual on how the heck the controller board works. I was able to get the machine to move but it won't move just a little bit, if you tell is to go X neg it goes until it...
  10. 1290 Gweike Just got it powered up and trying to figure it out

    Does anyone have a decent manual on how the heck the controller board works. I was able to get the machine to move but it won't move just a little bit, if you tell is to go X neg it goes until it...
  11. Replies
    19
    Views
    1,972

    Got the pictures!!!

    Lucy
    Thanks for the pictures of my machines. They look very nice. It is cool to see the inside of your warehouse and see all the activity going on there.
  12. On the 4th axis you can not use the back plane as...

    On the 4th axis you can not use the back plane as it relates to the top view. The way we get around it is to use dynamic plan to create a view that will roll in the right direction without needing...
  13. Replies
    19
    Views
    1,972

    thanks for all the info everyone. I am being...

    thanks for all the info everyone. I am being told that my machines will be ready to ship by Saturday. So the journey is almost underway.
  14. Replies
    19
    Views
    1,972

    Wolfau, Thanks for all the info. I did get the...

    Wolfau,
    Thanks for all the info. I did get the cw5000 chiller with mine. You said get a fuel filter? Could I just use a whole house type of filter system? Is it just to stop particles from going...
  15. Replies
    19
    Views
    1,972

    Yes this will be my first laser but I do have...

    Yes this will be my first laser but I do have over 20 years in machining / CNC Programming so Im hoping for the best. I have been reading up on what all mods everyone does to these. I think the...
  16. Replies
    19
    Views
    1,972

    I suppose that is one way to look at it. lol

    I suppose that is one way to look at it. lol
  17. Replies
    19
    Views
    1,972

    Thanks!

    Thanks ffokazak, that is part of why I finally got this done. I have been watching this forum since early Nov and there is so much good information on here and so many people willing to help out...
  18. Replies
    19
    Views
    1,972

    Placed the Order Today Thanks Lucy!!!

    Well I pulled the trigger and placed the order for my LC1290 from G Weike today. So the wait begins... Thank you Lucy for being super patient with all my questions.

    Brandon
  19. Replies
    21
    Views
    8,455

    some thoughts

    Your code looks right as far as the two lines you say are giving you trouble. Double check that your G54 is set correctly. Also if you are just wanting to move your table away before tool changes,...
  20. Replies
    5
    Views
    4,998

    STL

    An STL file does not have surfaces on it that you can machine. You will have to ask for a different file format.
  21. Just modified our posts to put: G0 G90 G154 P99...

    Just modified our posts to put:
    G0 G90 G154 P99 X0 Y0

    Just put that in right before the M30 and your table will go to that fixture offset position so you are not locked into a hard code table...
  22. Replies
    5
    Views
    609

    boundry

    The problem with Silhouette boundry is it creates a bunch of little splines and can make your cut look choppy sometimes. If you just translate the original geometry then you do not have that...
  23. Replies
    10
    Views
    3,173

    I think the only way this could be done in...

    I think the only way this could be done in mastercam is using a lollipop cutter and programming it fully 5axis. That is how we would do it at my shop. I think before we went to that time and...
  24. Replies
    5
    Views
    609

    quick fix

    Just do an xform translate to a plane. you can select all the chains you want to include in the profile and they will all be translated to a single plane. then you just have to trim them all...
  25. Replies
    13
    Views
    1,683

    I am new to this board and I am getting closer to...

    I am new to this board and I am getting closer to my decision on where to buy my first laser. I have looked at several differant ones since I started this journey a few months ago. I have been...
  26. Replies
    27
    Views
    3,931

    I am new to this board and I am getting closer to...

    I am new to this board and I am getting closer to my decision on where to buy my first laser. I have looked at several differant ones since I started this journey a few months ago. I have been...
Results 1 to 26 of 26