The problem has been solved, now I will sleep .
I contacted FIVES, they helped me with a zip file to change the parameters on the BIOS of the RTCPU board.
The files not only change the parameters...
Type: Posts; User: Chivo
The problem has been solved, now I will sleep .
I contacted FIVES, they helped me with a zip file to change the parameters on the BIOS of the RTCPU board.
The files not only change the parameters...
Hello Gwood, thank you very much for the information. The problem persist. I have to changed only the ultra DMA2 to disable.
I more than sure that the problem must be the parameters for the BIOS...
part number of the WSCP Assembly 3-424-2290A02 REV:E
hello gwood
The batteries from RTCPU and WSCPU boards were changed the same day. WSCPU board parameters were changed only the date and hour. It is the second time I have changed the batery from the ...
About the 2 leds. on the profibus card during startup.
The 2 leds on the card, one led is the color red at the biginning (far from the conector, will call it #2 )
some time later "1:30 minuts", ...
500520
500522
500518
All lights are in green
500478
this is the ALARM'S PICTURE
The BIOS was cleaned removing the battery
Tomorrow I will take a picture of the profi dp.
The RT CPU board has a different part number from the...
Hello gwood, thank you for the 2 BIOS SETUPS
the Profibus card is next to RTCPU.
I have tried the 2 BIOS OPTIONS attached, they are not working.
"ALARM 40-33 Output/Fuse Failure in APC Rack 0"...
Thank you very much for the BIOS`s parameters. There are a few parameters extra in my bios. My board has an AMD processor.
500396
500398
500400
The problem with the CONVENTIONAL SERVO...
Hello, The capacitor was soldered but the problem persist.
the Board ASSY# 3-424-2379A02 revison A. Maybe somebody has the parameters for the BIOS.
The model of the board is G7VP2 rev: B1
I am...
If you provide the Board ASSY# 3-424-xxxxAyy found on the board Chassis to the "Forum"; maybe someone has documented what they were on a bench while they were correct
499764
hi, GWOOD.
The DV5 board is givingme a fault led light. I have isnpected the pcb board and one 22uf 20v tantalum capacitor had a broken leg. I´m waiting for the fixing of the card to test again....
499344
499346
499348
499350
Hello, please some help. I have a Cincinnati Arrow 2 750 with Acramatic 2100 control. It has the servo drivers made by siemens.
The machine was working ok, I recently had a problem with the date...
Hello
Please some help.
I have a Cincinnati Arrow 2 with Acramatic 2100 - and Siemens Simodrive 611 drivers.
Yesterday the machine was Ok, today the machine can`t work, the servo driver X,Z...
Problem fixed. Hard drive software corrupt.
I had an image of the hard drive of 5 years ago.
Changed hard drive and the machine is OK. now.
Formatted the original hard drive and load the hard...
Please any one can help me with this problem with a Cincinnati Arrow 2 EKK with acramatic 2100.
465440465442465444
The proximity sensor was broke, because one spring washer was broke in half and one part slide out a little bit, like an ax it cut the proximity sensor.
Sharing some cad drawings from some CINCINNATI SPINDLES.
Hello.
I have a Cincinnati Arrow 750 EKK Series 2, with all Siemens: servo drivers,servo motors, motor spindle. and Acramatic 2100.
The spindle is hi-torque 5000rpm spindle.
I want to replace...
Hello
Does any one has this manual:
ACRAMATIC A2100E / SIEMENS SETUP & SERVICE MANUAL / 7-000-5938IS
Recently I purchased 4 bearings for a cincinnati arrow ballscrew support. Each pair were purchase in EBAY from different vendors and the 4 bearings are counterfeit. DON'T BUY PRESICION BEARINGS ON...
Hi, some help ( hitachi seiki ht30J / SEICOS 300J)
I was changing the control's membrane (big control keyboard), so I had to remove the 2 PCB boards from the front control cabinet.
After...
Hi
The spindle from my Arrow2 EKK 5000RPM, failed. One washer springs broke and damaged a sensor. I pulled down the spindle and now I'm trying to refurnish the spindle.
Does any one have...
The proximity switch is broke. I'm going to replace it. Hope this solve the problem.
Hello.
Please some help with a Cincinnati Arrow 2 - Siemens Servo drivers - Acramatic 2100.
The problem is when the machine is homing. The spindle rotates 6 times and it can not get the home...
Hello, I am having the same problem with my X axis Cinci. Arrow2 - 750 (it has scales) But it sounds only in one part of the x travel.
Can you help me with the test procedure from FIVES?
On the machine once you call up the file to look at it you can change it when you exit out of the file there should be an option for exit and save.
Robert Varney,
Application Engineer
...
On your pc put a copy of cnc_com in a directory\folder by itself. Start cnc_com in a dos window\dos prompt. In file maintenance go to copy file. In there you will see copy from and copy to.
Copy...
Open the attached main.plc file in windows notepad and compare to what you have. Do not try to copy this file into your control you can only compare it and make manual edits if you need to. The...