584,849 active members*
4,559 visitors online*
Register for free
Login

Search:

Type: Posts; User: freakycnc

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    25
    Views
    6,593

    Re: pin out pulse coder A860-0360-v501

    From the Date on the motor tag shown and the FB unit being off-center I'd say it's an inductosyn resolver.
  2. Re: Help! Fanuc 18t RS 232 File Read & Write

    zeroexa,
    It may be that the PMC is in ONLINE mode. Check parameter 24.
    If it is anything other than "0" it may indicate that "ONLINE" was turned on at some point.
    Try change to "0".
    You may also...
  3. Re: Fanuc 180i MB - changing parameter 3202 bit "NE9"

    zavateandu,
    This has me intrigued. I have run into this a few times working for a dealer and thought there must be a better way other than re-loading SRAM.
    Could you be a little more specific?...
  4. Re: WTO live tool box for swiss lathe strange sound after power outage

    Does the same noise occur if you run the tools in the opposite direction?
    I've had similar situations where the servo amplifier was not firing correctly in one direction (+) but OK in the opposite...
  5. Re: Reading axis position and tool offsets by an external PLC

    Fanuc has a function "Position Switch".
    When an axis reaches a predetermined position, set by entering position in parameter, the control turns on an output F70, F71 (and others for direction) which...
  6. Re: Fanuc 21M - MV40E DRO Updating but no movement

    Leet,
    Have you checked interface diagnostic G108.2?
  7. Re: Mazak Win95 controllers - loss of SMB1 networking protocol

    Don't know about the Mazak controls but Fanuc has a tool "NCBOOT32.EXE" on the Windows controls that will allow you to start a program/batch file from an external source (Storage card).
    Usually...
  8. Replies
    4
    Views
    625

    Re: CHIRON FZ 16 FANUC 10

    The experience that I have on the older Chiron with the Fanuc control used a Siemens PLC.
    Chiron used the BMI to communicate with the PLC and all of the timers, counters and parameters for the PLC...
  9. Replies
    5
    Views
    621

    Re: Robodrill Turret

    There are cases of this noise being caused by a parameter issue and gain being too high.
    As the mechanics wear the static friction becomes less and the spindle servo gain is too much causing...
  10. Replies
    2
    Views
    594

    Re: FANUC 31i-B5 Model

    There's a backup (FROM) on the restore menu on iHMI
  11. Replies
    10
    Views
    1,093

    Re: Matsuura RA3 pallet changer

    Here's Matsuura 40 taper BT spec
    486644
  12. Replies
    10
    Views
    1,093

    Re: Matsuura RA3 pallet changer

    usolutions,
    The "Rapid Arm" (hence RA) is driven by a rack and pinion on X axis. With no pallet connected the rack is not engaged and the arm can move freely.
    The manuals have an installation...
  13. Re: NEED HELP Matsuura MC-1000V with Fanuc 11M

    steve0311,
    "56" from the manual says to refer to "63" and "64" for explanation.
    "64" says to operate the INTERMEDIATE-ARM by the panel below the tool magazine. There are LED's indicating position...
  14. Replies
    3
    Views
    1,205

    Re: Matsuura MC510 VG

    Makro40,
    2180 is an indicator that the PLC is in alarm. To read the alarm you must go to ALARM then "USER" soft key for details of the message.
  15. Replies
    4
    Views
    548

    Re: 6M Parameters

    Tanoga,
    These are option parameter settings: Helical cutting, G10 input, Tape verify and more Offsets.
    These don't interfere with RS232 operation.
  16. Re: Windows service get stuck and spike cpu usage on calling FOCAS cnc_allclibhndl3 f

    fabriziocs,

    Have you tried varying the "timeout" in your handle call?

    cnc_allclibhndl3( "IP ADDRESS", 8193, 10, &h ) --- in this case it's 10 seconds -----

    timeout [ in ]

    Specify...
  17. Replies
    3
    Views
    644

    Re: Makino FNC106 internal error

    Lee,
    It seems the control is powered on from your description.
    Usually this condition is an interlock from the ATC arm not being at 'standby'.
    I'm assuming a Fanuc 6?
  18. Replies
    4
    Views
    1,061

    Re: Matra Fanuc tape cut w2 Help needed!

    Pentti,
    436 alarm could be 'soft disconnection alarm'.
    Record the value in parameter 2064 (to put back if test does not work) for the U axis then make it 100 for test to see if the symptom changes.
  19. Replies
    11
    Views
    3,770

    Re: Removing 4th Axis from Table, Fanuc 0i

    Seelesturm,
    Change parameter 12.7 and 1005.7 for the 4th and 5th.
    There may be a "Dummy Connector" hanging near the 4th, 5th electrical connections. If there are, plug them in after disconnecting...
  20. Replies
    1
    Views
    1,237

    Re: Positive Pallet Identification

    Brad,
    The control will send the machine pallet number to a macro variable.
    You have to set the variable number in DATA TABLE D12420. (System, >, PMC MAINT, DATA, OPRT, ZOOM)
    You have to make...
  21. Replies
    2
    Views
    429

    Re: Fanuc protected files SRAM

    Evil,
    In your example (-34.jpg) the file for digital servo is the subject, which is a Fanuc System file
    NCBOOT32 allows only "USER" files to be retrieved from the system IE: CEX, PMC Program,...
  22. Replies
    1
    Views
    453

    Re: 3M Diagnostic Parameters

    copper460,
    The DGN parameters are determined by the machine tool builder when they wrote the sequence program.
    Maybe they are listed in the documentation for the machine.
    You'll have to track down...
  23. Re: Matsuura MC-710V Manuals and info on spindle lubrication?

    -hh
    The phase rotation should be set to CW at the main breaker - there is a phase reversal check relay in the cabinet that will not allow the machine to be powered on if it is not CW.
    Any attempt...
  24. Re: Matsuura MC 500-v2 Intermittent 333 Fuse (Z) Blown Alarm

    smoran22,
    I would not take the encoder off the motor. There is an access plate on the front of the casting that you can reach the motor coupling and rotate the ballscrew by hand.
    If you remove the...
  25. Re: send and receive part programs from CNC –PC with FANUC CNC

    JUANCARL,

    Your control would need to be the " i " series with "Extended Drivers and Libraries" function (FOCAS) option for this to work for either RS-232 or the OSI/Ethernet connection.
  26. Re: Insulation Test Results - Can't Wrap My Head Around It

    Here's what Fanuc says about testing with megohmeter:

    - - - Updated - - -

    OOOPS...

    477196
  27. Re: Matsuura MC 500-v2 Intermittent 333 Fuse (Z) Blown Alarm

    You can download a book for the MR-K drive from Yaskawa - Downloads.
    The manual says "replace the controller unit".
    One thing you don't want to do is swap the top boards with other units as you may...
  28. Re: Matsuura MC 500-v2 Intermittent 333 Fuse (Z) Blown Alarm

    Which of the RED LED's is on?
    Brushes may need a good cleaning, also.

    477056
  29. Thread: View Ladder

    by freakycnc
    Replies
    1
    Views
    414

    Re: View Ladder

    Josh,
    #5555, ZOOM, INPUT on PMC Ladder screen
  30. Replies
    9
    Views
    917

    Re: 16i-MA 4th Axis Behaves as an Index???

    tcomm,
    Maybe check/adjust the values of parameter 5501 bit 0 and 1
Results 1 to 30 of 85
Page 1 of 3 1 2 3