507,855 active members
2,254 visitors online
Register for free
Login

Search:

Type: Posts; User: Jmhx2

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    49

    Re: UB1 Wiring Questions

    1. I thought that may be what you were doing. In that case, I think on the output I would install a fuse of less than 70mA.
  2. Replies
    4
    Views
    49

    Re: UB1 Wiring Questions

    1. Yes you can wire your inputs with external 24vdc supply. However, "Y" ports are outputs, not inputs. Inputs are "X". See page 12 figure 10 (a). You need to use inputs X310-315.
    2. I think I read...
  3. Re: CNC Wood Routing & Milling Machine/Software Laguna IQ 4’ x4’ 12” Gantry

    Interested in Aspire if willing to separate.
    thx
  4. Re: Spindle question Control spindle speed via UCCNC

    Take a look at ugracnc.com, I have had very good experience with their products. They have air and water cooled spindles and multiple VFD's. I run Hitachi VFD and 2.2kw ER20 air cooled spindle. The...
  5. Replies
    8
    Views
    69

    Re: Looking for a face mill recommendation

    Off topic - but does your Z axis make a wine or resonance sound when rapid up or down? Mine does, but have not had the time to investigate yet.
  6. Replies
    7
    Views
    130

    Re: CAM model to level sacrificial bed

    [QUOTE=ShaneMinnear;2313240]Hi All

    Try removing "G28 G91 Z0" and run again.
  7. Replies
    5
    Views
    79

    Re: CNC motherboard advice

    I have just installed my second UC300eth-UB1. One in a router and the latest in a mill. I really like the layout of the board, sufficient number of I/O, 24VDC I/O, and the ease of install. I don't...
  8. Re: Anyone considering the centroid Acorn instead of path pilot?

    The 8pin connector receives wires from the 6 &4 pin connector and it outputs back to the 4pin connector in the harness, that feeds to the vfd. There is a schematic at the bottom of the install manual...
  9. Re: Anyone considering the centroid Acorn instead of path pilot?

    Agreed, I had issues withe mach3 plugin. Purchased the Mach4 plugin for testing and it wouldn't support my PCI based controller. That's when I went to UCCNC and DMM servos and have never been more...
  10. Re: Anyone considering the centroid Acorn instead of path pilot?

    Thank you for the information, I went out and did a little reading. I used to use a Galil controller on my router. I assumed the acorn was similar but see that it is not. It appears the Oak...
  11. Re: Anyone considering the centroid Acorn instead of path pilot?

    Did you get your PDB setup yet? I just did this a few weeks ago while installing UCCNC / uc300eth-ub1 in my new Torus build.

    *Take note* There are 2 white wires, one is spindle direction (pin6)...
  12. How to configure a soft stop button - Not E-stop

    I have been trying to come up with a soft stop for a while now and the solution is not coming to me. Looking for ideas.
    I have UC300eth-UB1, UCCNC, DMM Dyn4 servos.
    I have wired the UB1 with a...
  13. Re: CNC4PC slow customer service UCCNC license second time

    Arturo, the file has arrived. Thank you for your attention to this matter.
    You saved me from disassembling my router to progress on the mill this weekend.
    Jon
  14. Re: CNC4PC slow customer service UCCNC license second time

    Agreed, I should have done that.
  15. CNC4PC slow customer service UCCNC license second time

    How long should it take to generate a software license?
    Maybe I am being a crybaby, but the internet has spoiled us into receiving items like this within minutes. Shoot, Amazon delivers products to...
  16. Re: Help with Schaffner EMI filter and DNY4 installation

    Nice layout Swath, I am currently wiring my cabinet with similar components. Wish I knew this filter information before I purchased. I am using one 30a for mains and 1a filter per logic lines. It...
  17. Replies
    8
    Views
    37

    Re: WJ200 High Frequency Mode

    Maybe I wasn't clear, the vfd will drive the high frequency motor. I run a 24k rpm motor on the drive. I meant there isn't a setting that "switches" it to high frequency.
    If it is a std WJ200 then...
  18. Replies
    6
    Views
    70

    Re: BLDC Motor needs a new Controller

    From my experience you need to be more concerned with the amperage for the bldc motor. That way you will maintain the current torque. Less volts equals less speed.

    Sent from my Pixel 2 using...
  19. Replies
    8
    Views
    37

    Re: WJ200 High Frequency Mode

    There isn't a high frequency mode. The vfd operates from your motor settings input. Verify the following settings with your motor data. a004, a003, a082, a044, b012, h003, h004.

    What motor are...
  20. Replies
    9
    Views
    198

    Re: Servo recommendations

    My two cents:
    I built a similar router ten years ago and used a dedicated control (galil) with Parker brushless servos. It used a plug-in for Mach 3 to communicate with the galil. It worked, with...
  21. Re: Novakon Torus Pro Servo edition for Sale Austin Texas

    If still available can you PM me so we can exchange #'s?
    Jon
  22. Replies
    8
    Views
    182

    Re: Need help with proximity switch setup

    Is the demo version limited for controlling outputs?

    Sent from my SM-T813 using Tapatalk
  23. Replies
    11
    Views
    1,489

    Re: EPIC fail on 3d relief Need help!

    Looks like your finish pass took away too much material. (The area for the fish tail should not be so deep. It should be approximately the same height as your rough pass). Did you zero to original...
  24. Replies
    16
    Views
    1,606

    Re: WJ200-022sf and 2.2kw Spindle settings

    Yes, that is the next project when I find some time.
    Found a video that appears simple enough.
    https://www.youtube.com/watch?v=L7QT1B0yAfA&index=4&t=17s&list=WL
  25. Replies
    16
    Views
    1,606

    Re: WJ200-022sf and 2.2kw Spindle settings

    Well it has been some time since I started this post and I was at the end of my rope and ready to purchase a new spindle. Then Andy at UGRACNC came to the rescue. That states volumes to their...
Results 1 to 25 of 119
Page 1 of 5 1 2 3 4