Sound like the VFD is introducing EMI into the ESS and causing it to fault. You could try to use ferrite beads on the DCM and FOR wires coming into the relay board, or better yet would be to use a...
Type: Posts; User: eman5oh
Sound like the VFD is introducing EMI into the ESS and causing it to fault. You could try to use ferrite beads on the DCM and FOR wires coming into the relay board, or better yet would be to use a...
You can input your info here https://fswizard.com/www/ to get the cutting force after you enter your cut details, just click on the blue bar near the top of the screen to see the cutting force.
If you have an indicator you can check the spindle for runout....that should tell you if it is the problem.
What he said, the G28 is a return to home command.
One other option is to trade $$$ for time, most material suppliers will cut your material to rough size for a nominal cut fee.
When was the last time you checked the gibs adjustment? If you have a loose gib you would see a problem like what you describe.
It may be a controller setting issue. I don't use Mach 3 any longer but I do recall it has an exact stop mode and constant velocity mode with some setting for tolerance. Those may not be the names...
I have 3 gecko 203V drives for sale they are used but working condition. See the ebay link below, I will take $200 for them with a direct pay-pal, or if you are not comfortable doing that I can...
The clear path motors do not need a driver so you will need a breakout board to interface them to the computer, either the lpt port or a mesa fpga card. You will need a breakout board and you could...
I did not realize it was a G540, In that case just a 5i25 or 6i25 and a cable will work for interfacing straight to the G540. I believe there are even premade G540 config files for the MESA cards.
The clear path will run on step and direction signal, so the combo I mentioned will work for that. If you want to reuse most of what you have you could remove the smooth stepper and replace it with...
If you are running steppers the 5i25with 7i76 cards are great combo, I am using it to run a Bridgeport BOSS mill with steppers and a vfd spindle.
You will need to switch your post processor to one for linux cnc and repost your files as linux cnc has different requirements than mach 3. I switch from mach3 to linux cnc as well, once you get...
I am running a Bridgeport BOSS5 Mill with G203's and would like to compare the performance of the new G214 with the big Nema 42 motors.
For different manufactures it means different things, but to me a true digital servo is one that the pid control loop runs in software on a processor opposed to analog electronics.
That sounds more like you have an enable and a direction contact. My vfd works that way but it is controlled with Linux CNC. I am sure Mach would be able to be configured like this as it is a fairly...
Short answer is yes more voltage will increase the torque at speed, the long answer may be found by reading this...
A quick look and I see ch0->InputMode=ENCODER_MODE while the rest are set to NO_INPUT_MODE; not sure if you this was your intention but does not look right.
It has a braking transistor, it does work but will trip if I set the decel to less than 5 seconds and have the spindle spun up to 4200 rpm. I am hoping once I remove the vari drive parts and put in...
It's a TECO L510 2HP...
Yes, things you learn the expensive way..... I was hoping to save others an expensive lesson. The VFD I used is rated 2HP while using single phase input, but it does not perform well and has no...
I already have the VFD on my mill and am looking to do a 2:1 pully set as described here Bridgeport Boss 5 retrofit - Pirate4x4.Com : 4x4 and Off-Road Forum I have a Teco 2HP VFD on mine and if I...
I am running mine with stepper right now and plan to go to servo's for smoother low-speed motion and higher precision. The original stepper that come on the BOSS mills do not like to micro step so...
I just retrofit a Bridgeport Boss5 mill with Linux cnc, I was shopping around and was considering a manual Bridgport as well, but changed corse when I started costing out the 3 ball screws needed. I...
Looks like you are losing steps or have something that is slipping.
Only the 460 volt L510's can have a braking resistor. Being for hobby use the time it does not bother me in the slightest. My problem is that I want to either get ridged tapping or a floating head...
I am running a 2 hp vfd on a 2 hp motor, I guess I should have up sized it, I turned up all the parameters and the acceleration and braking still leave a bit to be desired. If I replace it, it looks...
The pendant looks just like this, I got it from ebay but I am not sure of what seller I purchased it form. Universal CNC 4 Axis MPG Pendant Handwheel Emergency Stop F Siemens Fagor GSK | eBay
See post #6 in this thread
http://www.cnczone.com/forums/dynomotion-kflop-kanalog/285552-mpgsmooth-c.html
The install looks great, I have the same vfd on my Boss 5 Linux CNC conversion. I have been unimpressed with the vfd performance. Mine seem to take 4-5 seconds to spin up or down the spindle to full...