584,833 active members*
5,770 visitors online*
Register for free
Login

Search:

Type: Posts; User: orbets

Search: Search took 0.00 seconds.

  1. Replies
    7
    Views
    5,503

    Re: Amada Vipros 357 Oil Pressure Fault (stop)

    493762

    - - - Updated - - -

    493764
  2. Replies
    7
    Views
    5,503

    Re: Amada Vipros 357 Oil Pressure Fault (stop)

    I did.
    On the front end of the machine, there is a cover that houses the relay board (pic Location on machine), If you see evidence (or still have mice like we did) living in that area, they have...
  3. Replies
    0
    Views
    3,571

    Amada 357 Hydraulic clamps not working

    Hi all,
    Have been having an issue with the hydraulic clamps not clamping properly. The e-stop light was staying lit for about 10 seconds after clamping and then going out and I was able to...
  4. Thread: NEED HELP

    by orbets
    Replies
    16
    Views
    2,409

    Re: NEED HELP

    I had the same problem. Check the above replies. A faulty reposition sensor below the table will cause the machine to stop and make it appear that it's an A/I issue. Take off the small corner pieces...
  5. Replies
    0
    Views
    622

    Lost parameters on Vipros 357 HELP !!

    Changed the 3 AA batteries in the PHNC cabinet yesterday (machine was running) and this morning trying to start up, it looks like I've lost some parameters. PHNC is now in Chinese. Went to the...
  6. Replies
    2
    Views
    1,536

    Re: Amada NC9-F Control Parameter help needed

    Thanks amadajoe. I'll give that a try. Next will be the 5lb sledge hammer.
  7. Replies
    2
    Views
    1,536

    Amada NC9-F Control Parameter help needed

    Hi all,
    Been trying to get into the Parameter portion of a NC9-F Control on my FBD1030. When I press the "Internal System" button and press Parameters, nothing happens. It is not asking...
  8. Storing date from NC9-F (Amada Brake Press) through RS232 port

    Looking to find out how to send & receive data from the control panel by using an external computer.
    The machine is an Amada FBD-2512 with a NC9-F.
    Any ideas?
  9. Replies
    7
    Views
    5,503

    Re: Amada Vipros 357 Oil Pressure Fault (stop)

    Have narrowed the problem down to the "Shut Off Valve". We removed it to inspect and the solenoid itself appears to be intermittent and sending a signal whenever it wants. There is a small board with...
  10. Replies
    7
    Views
    5,503

    Re: Amada Vipros 357 Oil Pressure Fault (stop)

    Hi,
    Yes, we still have the problem but have been using in F3 & F4
    Any thoughts?
    Thanks.
  11. Replies
    7
    Views
    5,503

    Amada Vipros 357 Oil Pressure Fault (stop)

    Sorry for the lengthy explanation.
    We are getting a stop alarm during the punching sequence showing "OIL PRESSURE"
    The pump pressure slowly drops from 22Kgf to 15Kgf and the stop appears.
    On...
  12. Thread: NEED HELP

    by orbets
    Replies
    16
    Views
    2,409

    OK. Found the problem today after many, many...

    OK. Found the problem today after many, many hours and lots of covers removed.
    There are 2 sensors located below the table on each side of the turret that are supposed to sense the stroke of the...
  13. Thread: NEED HELP

    by orbets
    Replies
    16
    Views
    2,409

    The stations themselves are all ok now. I...

    The stations themselves are all ok now.
    I cleared out the slugs around the A/I and tried to push down & lift up the drive pin with out any luck.
    It does now look like its in the correct position....
  14. Thread: NEED HELP

    by orbets
    Replies
    16
    Views
    2,409

    New information. The A/I had just finished the...

    New information.
    The A/I had just finished the punching cycle and was about to move to the next tool when the error occured.
    Now I'm leaning towards a mechanical problem. ie: a slug?
    I need to...
  15. Thread: NEED HELP

    by orbets
    Replies
    16
    Views
    2,409

    ok. not the problem. checked the A/I stations...

    ok. not the problem.
    checked the A/I stations again.
    While turning the turret by hand to check each A/I, it came to a hard stop.
    The coupling (below bottom turret) on one of the A/I stations that...
  16. Thread: NEED HELP

    by orbets
    Replies
    16
    Views
    2,409

    Hi, It is an O4PC. The index pins do engage...

    Hi,
    It is an O4PC.
    The index pins do engage before it boots up.
    Where should I be looking for relay SHP?
    Is the switch in the PNHC panel or the Main Control panel?
    Thanks
  17. Thread: NEED HELP

    by orbets
    Replies
    16
    Views
    2,409

    I have the same problem ERROR 2000

    Hi,
    I'm having the exact same problem today on my Vipros 357.
    The inex pins are out when the machine is off.
    They engage when started.
    So I am assuming that the switchs actually work
    I can not...
Results 1 to 17 of 18