Search:

I am sorry i have not been back here for a while now sir. Yes i do need the info on the drive and how to control it away from
the mitsubishi control. I would like to control it with step and...

I have a 4th axes from golden sun. The servo motor on it is a 1 kw 3 phase ac motor model number (HA 80 NT- E 30).
I have no servo amp but it looks like i need a (MDS-A-SVJ-10).

I need some one...

HI SIR

I HAVE A DECKEL FP4A AND YOU HELPED ME IN THE PAST WITH VALUBLE INFO ON THE RS 232 INTERFACE ON MY CONTOUR 2 CONTROL.
I HAVE SORTED ALL AND JUST LOVE THE MACHINE. SUCH QUALITY MACHINES IF...

HI SIR
CAN YOU TELL ME IF I CAN USE BT40 TOOLHOLDERS ON MY DECKEL FP4A AS IT USES ISO40 WITH HYDROLIC CLAMPING ?
CAN I GET A ADAPTER TO SCREW INTO THE BACK TO FIT MY HYDROLIC CLAMP OR EVEN MAKE...

HI

I AM TRYING TO BUILD A 4TH AXES FOR MY DECKEL MILL. THE QUESTIONS ARE MANY BUT CAN ANY ONE HELP?
I HAVE A STOBER AC SERVO MOTOR AND TREE PHASE AC SERVO DRIVE.
THE SERVO MOTOR RATED 7000 RPM...

HI ALL
I GOT HOLD OF A COMPLETE FANUC 6TB CONTROL IN WORKING ORDER.
I HAVE THE TAKISAWA TX 210D LATHE WITH FANUC 6TA AND LED DISPLAY UNIT.

CAN ANYONE TELL ME HOW TO USE THE CRT PANAL ON MY...

HI EVERYONE.

I AM LOST BETWEEN I THINK 4 PEOPLE WHO IS TRYING TO MAIL ME A COPY
OF DRIVE TOP SOFTWARE FROM ALL OVER THE WORLD.
NOT ONE SEEMS TO GET IT RIGHT.
I AM NOT SHARP WITH COMPUTERS BUT...

HI I WANT TO CONVERT MY ORAC LATHE TO MARCH3.
CAN I USE THE ORIGENAL SPINDEL DRIVE ELECTRONICS.
IS IT A 10V ANALOG INTERFACE OR HOW DO I CONNECT IT
TO MY BREAK OUT BOARD ?

REGARDS
DANIEL

HI DO ANYONE KNOW THE DATA ON VEXTA FXM250B AC SERVO MOTOR.
COIL 14.9ohm
APPEARS TO BE DELTA CONNECTED.

ENCODER MEP 102 (ST6 14125)

14 PINOUT RED AND BLACK (I THINK 5V FOR LOGIC)
REST IS 6...

I HAVE SOME INDRAMAT ECO DRIVES (DKC01.1) AND CAN'T FIND THE SETUP
SOFTWARE ANYWARE.
ARE THESE DRIVES STILL SUPPORTED AS THEY DON'T LOOK THAT OLD?
WERE CAN I FIND SERVO MOTORS THAT WILL MATCH...

HI HEIN I HAVEN'T BEEN BACK TO THE FORUM IN MONTH'S.
I HAVE REPAIRED THE ELECTRONICS BUT IS STILL LOOKING FOR SOME
SPARES. THE MACHINE NEEDS NEW TURCITE FOR THE Z AXES.
I NEED A SMALL AMOUNT OF...

HI EVERYONE.
I HAVE BEEN TRYING TO GET HOLD OF 1.2mm TURCITE B SLIDEWAY FOR 2 MONTH'S
NOW AND AM LOSING HOPE. IS THERE ANYONE WHO CAN HELP ME OUT WITH A SMALL
AMOUNT OR KNOW WHO WILL DEFFINATELY...

HI CAN ANYONE HELP ME ON THE EXACT SPINDLE RPM,S ON MY LATHE.
IT IS A TAKISAWA TX210D PRODUCTION LATHE,1980 MODEL.
IT DOES NOT HAVE CONSTANT SURFACE SPEED CONTROL, ONLY S1,S2,S3,S4
AND THEN I...

SIR AT THE MOMENT I NEED TO FIRST PUT IN A PROGRAM MANUALY
AND TEST THE MACHINE FUNCTIONS ALL.

IF ALL IS WELL I WILL SPEND MONEY ON THE BTR AND SOFTWARE.
ALSO WANT TO CHECK THE MECANICAL...

SIR I HAVE A EPROM PROGRAMMER AT WORK.
CAN I BUY 994 VER 25 OR LATER SOFTWARE FROM YOU AND
PROGRAM MY OWN EPROM IC.

REGARDS
DANIEL

SIR I AM VERY ITERESTED IN THE BEHIND TAPE READER.
WHO CAN I CONTACT THAT MAKE ONE THAT IS RELIABLE
AND NOT TO EXPENSIVE?

I WOULD LOVE A COPY OF YOUR DNC SOFTWARE AND ANY PROGRAMMING
MANUAL ON...

SIR I DON'T HAVE THE SOFTWARE.
CAN YOU TELL ME IF I CAN REPROGRAM MY EPROM IC'S OR
MUST I GET COMPLETE NEW SET AND WHAT IS THE COST?

THE OTHER WAY I THINK IS TO GET A BEHIND TAPE READER
AND NO...

Hi sir i have the fanuc service manual and the param settings for different
baud set.
The punch interface card has two conectors,one for external puncher and
other for rs232. I will make up cable...

Hi sir my machine has got a flap on the front with a plug. Can you help me with
the setup of rs232 dripfeed?
I don,t have the programming manual so i can only do MIDI comands at the moment.
I dont...

Hi i have a takisawa tx210d lathe with a fanuc 6ta control.
It has only led adress and didgi readout but no crt.
Can anyone help me to enter a short example program and
how to run it on my...

I have a problem finding a programming manual for my lathe.
Not even fanuc looks like they want to help me.
It is a 1980 model TAKISAWA TX 210 D lathe with a fanuc 6T(A) control.

The control has...

GOOD AFTERNOON SIR
CAN YOU TELL ME IF THERE IS ANY WAY THAT I CAN FIGURE OUT THESE
PARAMMETERS BY TRAIL AND ERROR.
I ALSO DELETED THE CONTENS OF (OFX,OFZ,OFR AND OFT).
CAN YOU TELL ME WHAT THEY...

HI SIR (Memory Man)
IF YOU COULD HELP ME IN ANY WAY I WOULD BE VERY HAPPY.
MY MACHINE TX210D BUBBLE MEM MACHINE NO TAUNY0082
1980 MODEL.
I DONT HAVE SKYPE AT HOME BUT COULD GO TO A FRIEND....

HI SIR (AL The Man)
SORRY BUT THE OTHER NIGHT I FELL ASLEEP BEHIND THE MOUSE AND KEYBOARD.
ANYWAY IF YOU COME ACROSS ANY THING TO HELP ME I WILL BE VERY
GRATEFULL IF YOU COULD POST ME HERE.
I...

SIR IN MY MANUAL ON PAGE 112 AND 113 THEY TALK ABOUT (PC).
POWER SEQUENCE CONTROL.
MY RECEARCH INDICATE THAT THE PC PARAMMETERS ARE SET BY THE
MACHINE MANUFACTURER (TAKISAWA).
FANUC CANT HELP ME...

NO SIR NO STIFNESS ON THE BALLSCREWS WHEN I MOVE THEM BY
HAND POWER ON.
ALL THAT HAPPEN ON BOTH AXES WHEN I MOVE BALLSCREW IS AS
ENCODERS PIC UP MOVEMENT THE VELOCITY DRIVES TRIP OUT.
THE 3PHASE...

NO SIR NO SERVO MOVEMENT.JUST ERROR 411 AND 421 AS THE DRIVES
TRIPPED OUT.
THEN I RESET AND VREDDY BOTH DRIVES.
THERE WAS MOVEMENT AND ALL WAS FINE THE ONE MOMENT AND
THEN I PUNCHED IN SOMETHING...

HI EVERYONE.
I HAVE WORKED SOLID FOR ABOUT FOUR WEEKS NOW AND FINALLY MY
MACHINE MOVED ITS SERVO'S ON X AND Z AXES.
I ALMOST WENT TROUGH THE ROOF BUT MY JOY WAS SHORT LIVED.
I JOGED THE AXES AND...

HI I NEED ANY INFO TAKISAWA TX210D PRODUCTION
LATHE.
THE YEAR MODEL IS 1980.
THE CONTROL IS FANUC T6 AND HAS A HYDROLIC CHUCK.
CAN ANY ONE TELL ME WERE I CAN GET MANUALS ON THIS LATHE
AND IS IT...

HI EVERYONE THANKS FOR GREAT REPLIES.
MY DECKEL FP4A MILL HAS GOT A CONTOUR 2 CONTROLLER
3 AXES 2 1/2 D MILLING. I GOT A POST PROCESSOR FROM
DOLPHIN CAM BUT DID NOT GET THE INTERFACE CABLE WITH...