Search:

I haven't had any response to my issue, so I'm just dealing with it.

Yours looks more complicated. Maybe entire board, but it's also 18-T control. I have an O-T control. Try calling hardinge, you...

So today, 401 at power up. Same result as above. Top green LED lights for a second, then goes out. Hit E stop, then E stop reset, everything is good. Ran machine for 5 hours in a repeat cycle. Found...

Powered up yesterday, no issue and ran machine all day. Today I got the 401 alarm at power up. I had the rear cabinet open and was watching the 7 LED. There is also a green LED above and below all...

Can deal with the alarm, cannot deal with turret position changing. I'll try your suggestion.

I too am having 401 alarm on OT control. Usually at power on. I need to hit E stop and the reset and it usually clears. It must be a relay. I can hear something click if it works correctly. Sometimes...

MVIL, did the encoder fix your problem?
I am having an issue with my Conquest 42 with OT control. Always threaded beautifully with two line G76. Now it's cutting weird. Seems to be taking more off...

PU,1 for tool data
PU,2 for program
PU,3 for all

New issue. When the turret indexes it sometimes makes a sound like a sneaker on a basketball court. It's quick. But turret seems to operate OK. Aging equipment!!!!! Anyone have an idea?

Well we fixed the locknut issue and all was good for a time. This morning the turret went to index and made a deep sqeeking noise, but did index. It will always index OK, but sometimes makes the...

AN10 locknut alone backed off to the point of touching the gear. I guess if we spun the turret in the right direction it would have gone back on for the time being. ALWAYS USE LOCTITE in these...

Having a problem with our turret clamping fully. It's in but short about .040" of a tight clamp. Turret unclamp alarm now. Happened gradually over 15 minutes. Got the turret unclamp condition,...

Does anyone have any experience with Cimstar 40 and 60 xl. We have been running 40 for years. Recently we have come upon a bacteria problem which we never had before. Contacted Cicncinatti...

The stuff from FadalCNC.com, is it the same? Seems cheap.

OK, same thing a couple of months later, collet closer hangs up when actuating and there's a broken quad ring. This time it's in 2 spots, both over the check valves. There is a small holes under...

MadMax, I must have misstated. The quaud rong was never replaced with an O ring. Quad came out and quad went in. The pin hole I was referring to was the one in the piston, from the quad ring...

MadMax, yes I purchased them from Gosiger and used the schematic for the collet closer. I am confident it is correct. They were identical to the ones that came off, square shape instead of round....

Nawrocki4Life, I have changed ALL the O rings and seals. Yes, the quad rings seems to take the most abuse and I did change them. Did NOT change any pilot/check valve. Where is that located?
We...

MadMax, the quad ring is number 25 (0011151) on the collet closer schematic. Sits on the piston, part 40.
I have checked the housing no any scratches or nicks, very clean and smooth. Don't...

I have been reading some of the posts. I agree with most things said. The turret alignment on a live tooling machine is as easy to align as a non live tooling. At least on the early 90's models....

Works great! Seems like it's always been working, just not displayed. Parts counter was at 480,380.
What do you think the aux. function is?

parameter 907 on machine with parts counter read "01011010" on the other machine with no counter it reads "01001000" , so 2 bits are changed?
It's been awhile, also forgot how to enable PWE to...

Is a big deal to turn this feature ON in my other machine?

Works great, thanks. no need to go to parameter 600, can change it right on the PWE page.

Pressing "P" then "CAN" works like a charm, thanks.
Couldn't get to the PWE page by hitting offset button. Hardinge tek said the same thing, maybe I'm doing something wrong but I don't see the PWE...

Purchased another used Hardinge, same control as another we have. Noticed on position page it has a working parts counter and cycle time. Anyone know how to zero out the parts counter? Don't tell...

We have both, Fadal and Fanuc. Fadal fomat 2 is pretty much the same as fanuc. Format 1 is Yasnac.