510,008 active members
3,777 visitors online
Register for free
Login

Search:

Type: Posts; User: metalcutting

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Re: 1997 Daewoo LYNX 200A lost parameters. FANUC 21T

    Contact to support@quanutmautomation.com They will help you with parameters
  2. Replies
    12
    Views
    83

    Re: please help about okuma LB15 II MW

    Hope it will Help you

    G00 Positioning
    G01 Linear interpolation
    G02 Circular interpolation – Helical cutting (CW)
    G03 Circular interpolation – Helical Cutting (CCW)
    G04 Dwell
    G09 Exact stop...
  3. Replies
    2
    Views
    26

    Re: JOURNEYMAN 320 operating manual

    Take Help from support@quanutmautomation.com
  4. Replies
    1
    Views
    324

    Re: Service manual MillPlus

    you can take support from support@quanutmautomation.com
  5. Hi Every one , I have one Sharnoa VMC HPM 24...

    Hi Every one ,
    I have one Sharnoa VMC HPM 24 with tiger 5 control , The machine is running in Inches how to go in mm Mode ? Please help
  6. Replies
    1
    Views
    22

    Re: Help Wanted Mazatrol T2 Parameters

    Please share your machine serial number and year of Manufacture by PM
  7. Replies
    15
    Views
    258

    Re: OKUMA LATHE LB-3000 SPINDLE REPAIR

    Please contact on prabhatmishra74@hotmail.com
  8. Replies
    2
    Views
    203

    Re: Maho 1000 c

    communicate me on prabhatmishra74@hotmail.com
  9. Replies
    2
    Views
    52

    Re: Fanuc A14B-0067-B001 power supply

    Its very easy to repair , It has fuses , relay , a power contactor and PCB Fuse , If any help required let me know
  10. Replies
    1
    Views
    42

    Re: Floppy to USB drive emulator

    you want FLOPPY DRIVE EMULATOR make Haas or any compatible is ok to you
  11. Re: I need help to revive a 810 T GA2 control

    is it CRT or TFT ?
  12. Re: help with spindle motor winding resistance 10hp

    Make motor off line and put +05 -05 v in phase to phase and see the voltage dropping phase to phase and compare to earth
  13. Re: Fanuc 0iMC -9031 Motor lock or V Sig Loss

    TRY M 40
    M 41
    or check the motor
  14. Re: Takisawa lathe with fuji spindle drive issue

    Please check the input fuse of drive , than breaking resistor , and control voltage if all are ok , than check the scr module , alarm is of spindle or E stop ?
  15. Replies
    2
    Views
    183

    Re: Fanuc Test Stand

    Check the Motor cable and axis load , Jog in Low rpm and check the load
  16. Replies
    75
    Views
    7,181

    Re: What will happen if we give 60HZ supply to a 50HZ CNC Machine?

    you can use 60 Hz even it wont will effect the components , but 50 Hz is better while using in PWM and Phase shift circuits
  17. Replies
    1
    Views
    161

    Re: PULSECODER

    Both are alpha series pulse coder you can use
  18. Re: TNC 426 MP input (MP line w/o number error)

    ; start with it
  19. Re: 250 milliamp fuse blows when VF2 is off

    check the control circuit and wiring , also check the control voltage
  20. Re: Help needed Spindle drive connection on fanuc 6T- B model

    ENB 1 AND 2 ARE ENABLE SIGNAL WIRE VCMS FOR VELOCITY MASTER SPEED, NEED THE DRIVE PICTURE FOR CONFIRMATION , WHAT 'S APP - +91-9384248184
  21. Replies
    6
    Views
    415

    Re: Fanuc error 998 ROM Parity Error

    what is the ROM version
  22. Re: Hartford VMC 850 / meldasmagic64 / G03 causing locking up

    check the option param
  23. Re: Backup Parameters for cnc acramatic 2100?

    Look at :
    http://www.cnc.info.pl/files/a2100_operating_manual_166.pdf

    http://ftp.ruigongye.com/200807/91204426a001.pdf

    - - - Updated - - -

    Look at :...
  24. Re: spindle & VFD advice - can anyone point out what to look for?

    Take mitsubishi vfd . Its easy for hobbyist
  25. Replies
    42
    Views
    9,590

    Re: Amada pega fanuc 04pc system error

    Is it turret punch ? or
Results 1 to 25 of 38
Page 1 of 2 1 2