584,812 active members*
5,321 visitors online*
Register for free
Login

Search:

Type: Posts; User: cncdiag

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Tacchi lathe

    by cncdiag
    Replies
    0
    Views
    526

    Tacchi lathe

    Does anyone out there have a tacchi lathe.
    We have a HD/3,105 LS CNC
    I'm looking for.mechanical drawings
  2. Thread: OSP5020

    by cncdiag
    Replies
    1
    Views
    583

    OSP5020

    12v low voltage alarm, the power supply was rebuilt. What boards can I remove from the rack without losing memory?
  3. Thread: Parameters

    by cncdiag
    Replies
    0
    Views
    494

    Parameters

    Does anyone have a copy of the parameters for okuma Howa ACT 3 with a Fanuc 6 control and an ACT 5L with a Fanuc 11 control.
  4. Replies
    2
    Views
    979

    Cincinnati Falcon G73

    I need help programming a G73 in inch
    Can someone post an example.
    Thank You
  5. Re: Fanuc 6T, Lathe. blows one fuse on z-Axis-Driver

    Swap top cards
  6. Replies
    1
    Views
    703

    A1000 Spindle Drive

    Hello
    Has anyone upgraded there spindle drive to the Yaskawa A1000
    If so could I get a copy of the parameters.
    The sheet from Haas does not work.
  7. Replies
    2
    Views
    795

    Re: Fanuc 11M has no startup

    Whats the part number of the master board
  8. Replies
    2
    Views
    958

    Xaxis fault on TM1

    X axis goes into oscillation intermittently then will smooth out.
    No mechanical bind, swapped command and feedback cables so i am running off of the y circuit, fault stays with x motor , swapped...
  9. Replies
    3
    Views
    295

    Re: Forum for CNC refits

    What board is bad and what alarm are you getting?
  10. Replies
    0
    Views
    636

    Mitsubishi Spindle Drvie

    Does anyone have a copy of the parameters for a mitsubishi spindle drive on a 4020 machine
  11. Replies
    2
    Views
    997

    Re: Ikegai FX 25 N T5

    Reverse 2 of the incoming phases
  12. Re: Fanuc OMA 911 Ram Parity: (High) - Reloading Parameters Problem

    Have you loaded the 900 option parameters by hand and communication parameters.
    then you can upload parameters
  13. Replies
    0
    Views
    2,156

    Lynx 210 Hydraulic Pump

    Does anyone know where I can get a seal kit for the hdyraulic pump on the Lynx 210
    Its a Rotor Pump JRPV-15-L-01
    Its fitted on a KIR hydraulic unit KIR15P-11T-22M-A
  14. Re: Hardinge Conquest 42 troubleshooting - relay clicks on then off; no controler

    I would check the fanuc power supply, it has an alarm relay that can be used to latch the power on
  15. Re: OOYA RE-OM with Fanuc 6T control DC Spindle Drive problem

    Check the main fuses the alarm fuses are in parallel the main fuses, they indicate when the main fuses are blown
  16. Replies
    0
    Views
    736

    Johnford VMC2020

    Does anyone have a Johnford VMC2020 with a Fanuc 0 control.
    I am looking for a wiring diagram, the factory had a fire and lost wiring diagram for this machine.
  17. Replies
    11
    Views
    3,870

    Re: Kitamura MyCenter 2 With OM-B Controls

    Have you checked for 24vdc at the switches on the operator panel
  18. Replies
    1
    Views
    712

    Fanuc 0iMate on Yang

    We have a Yang SL20 with a Fanuc 0i control
    The ladder requires a password to view.
    Does anyone know the password????
  19. Replies
    2
    Views
    871

    Re: Digital AC Spindle EPROMS DAMAGED

    Did you load the parameters in the spindle drive
  20. Replies
    0
    Views
    613

    Fanuc Robot 420iR

    Anyone have a manuals for the Fanuc 420iR in pdf format they are willing to share?
  21. Thread: Fanuc 420iR

    by cncdiag
    Replies
    0
    Views
    1,282

    Fanuc 420iR

    Does anyone have manuals for the Fanuc 420iR in pdf format they are willing to share?
  22. Replies
    2
    Views
    2,606

    Turn on power holding in RESET and DELETE...

    Turn on power holding in RESET and DELETE pushbuttons to clear program memory
  23. Thread: Matsuura 510

    by cncdiag
    Replies
    0
    Views
    828

    Matsuura 510

    Anyone know the option parameter for Tool Offsets
    We have the Yasnac i80 control.
  24. Replies
    1
    Views
    795

    Mighty Comet VMC1000P

    Does anyone have a copy of the parameters for a Mighty Comet VMC1000P with a Meldas 300 control
  25. Replies
    6
    Views
    990

    Look under the spindle board there is a switch to...

    Look under the spindle board there is a switch to set for 200v or 220v.
    Set it to the voltage near yours
  26. Thread: 0A Software

    by cncdiag
    Replies
    0
    Views
    634

    0A Software

    Does anyone have a copy of the 412 or 414 software for the 0A control they can email me?
  27. over current/ field loss" on spindle acceleration or deceleration

    Swap any 2 phases of the incoming 3 phase power to the machine
  28. Replies
    6
    Views
    1,481

    Remove wires from the righthand side of power...

    Remove wires from the righthand side of power supply (make sure you mark them first) Remove white connector. Turn on control and check voltages on power supply, if you have no output voltages, check...
  29. Replies
    20
    Views
    4,987

    I was working on the same problem here. I tested...

    I was working on the same problem here. I tested the drive it ran fine. With motors disconnect I still had the same HC alarms both axis. With dummy plugs connected to servo control board I still had...
  30. Replies
    0
    Views
    730

    Parameters for SMG V48

    Does anyone have a copy of the parameters for an SMG V48 with a Fanuc 0M control?
Results 1 to 30 of 212
Page 1 of 8 1 2 3 4