Hi,
Ok, got the arcs sorted... When you change the Y coordinates in the variable section to -1 it works for straight lines. If you want the arcs to work to you have to invert the Clockwise and...
Type: Posts; User: bleker
Hi,
Ok, got the arcs sorted... When you change the Y coordinates in the variable section to -1 it works for straight lines. If you want the arcs to work to you have to invert the Clockwise and...
Hi,
Nobody ... ?
Does anyone maybe have the g-code and variable list for Biesse Rover CIX controller ? I have tried to change some of the variables to see if it will put the shoe down, but no...
Hi,
I have a "semi" working PP for the Biesse using Vertic Cut2d Pro. I had to edit the PP a bit to get it working and I can now make some cuts.
I still need to change the code for the dust...
Hello,
I need some help with Biesse Works command column. I can import geometry from cad on a TCH layer and get all my milling id's in listed in the column. How do I group the milling id's...
Hi,
Does anyone have a post that works with Biesse Rover machines..
Thanks.
Hi,
Thanks for the reply.. but it's no luck..
If the dip switch is in the normal position I get the "22 Check Sum error" and when the switch is in the other position I get the "25 NMI Servo...
Hi,
I went through the programing manual again and saw the section about Variables.. The common variables are only used when you are using Macro's so I must be able to get the machine running...
Hi,
Did you resolve this problem, I have the same issue except it is only the X and Y axis that move and they move in the negative direction.
Thanks
Hello,
I'm starting up an 1985 Mazak VQC 20/50b.. Needless to say the parameters where all lost, someone fitted new batteries, but I think the machine was down for too long before I bought it. I...
Hi,
Yes I got them to work.
Its all in the PDF.
I no longer use that BOB, I must have fried something while I was doing my final wiring. Think it was a ground or earth fault. I know I...
Hi Alan,
Thanks for the reply.
I have tried swapping the cables round, but this just lets the VFD run at top speed.
When I measure the voltage on the connector pins of the VFD it gives it to...
Huanyang VFD
Hi,
I have a 4Kw Huanyang VFD and air cooled spindle and they have been working hard for the past 6 months.
When I installed them I had them working through Mach, start, stop and...
Hi,
Does anyone know off or have a set of nice tool decals. I want to make a new toolboard for the shop. I thouth it would be nice to router out the tool places on the board.
Thanks.
Hi all,
After a busy couple of months and relocating to a new town I finally managed to get to work on my machine again.
Last week I did my first cuts on some 4mm plate. I cut some 50mm x 50mm...
Hi All,
I can't believe its been so long since my last post. As I have explained before this is silly season at work so there is not much time left for the machine.
I managed to get the x axis...
Hi All,
Unfortunately my work commitments have kept me rather busy the past week so I haven’t had time to do much work on the machine.
I got the sides welded on, they are strong and very...
Hi All.
Haven’t had much time to spend on the machine the past week, but got the motors running and picked up my side sections today.
I will make some gussets tomorrow and hopefully by the...
Hi all,
Thanks for the replies and in put on the connecting of the stepper motors and drives.
I struggled and cursed for two days to get them working and it was all due to one small setting in...
Hi All,
I need some help connecting my breakout board to my stepper motor drivers.
The breakout board is a Chinese HG05 make, does anyone know this board or has any experience with it.
My...
Hi all,
I received some more bits from China today, my stepper motors, controllers, power supply, breakout board and plasma cutter. Everything looks good and I’m happy with my purchases.
Not...
Hi all,
John:
Thanks for the input. I have thought off the rotating nut design, the Comac machine I spoke off earlier worked on this design. It’s a really good solution but complicated design....
Hello,
The 134 in/min is not that fast, I would like it to be more round the 300 in/min mark.
My other value I got from the calculations is 177 in/min and if I look at the charts on some...
Hi All,
Thanks for the replies..
Hawkmoon:
The steel tubes are costly same as the steel plate that I would need to finish the build. I calculated the steel for the machine at roughly $800,...
Hi All,
This is just a quick update on the build. I didn’t have a lot of time to work on the machine this past week, but got some work done.
The frame has all its supports in and the welding is...
Hi all,
This is my log on my new cnc plasma build. I originally planed a cnc router, but struggling to find someone with a cnc plasma to cut parts for the router, I decided to build my own cnc...
Hello,
Thanks for the replies so far. After posting last night I started to do some more calculations and realized how big the 45NM motors really are.
After some more thinking, I would prefer...
Hi all,
After operating the commercial CNC router at work I have decided that its time to build my own and start my own business. It must be able to cut a board size of 9’ by 6’. The board will...