584,846 active members*
4,418 visitors online*
Register for free
Login

Search:

Type: Posts; User: gguidi

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    929

    Re: Multicam sf stuck on panel rev screen

    Fixed we had to reload firmware.
  2. Re: SF Router M24 controller communication software

    Thanks, I got it figured out with some help.
  3. Replies
    1
    Views
    687

    Change screen orientation

    Is there a way to rotate screen? Now x is let to right and y is top to bottom. I would like the opposite. Thanks
  4. Replies
    1
    Views
    929

    Multicam sf stuck on panel rev screen

    I just purchased this machine and it was working from the keypad well. I downloaded pss motion program and established communications with it. I tried to send a gcode file and now it is stuck on...
  5. Replies
    2
    Views
    1,087

    Re: Multicam SF User Manual

    Thank you that will help.
  6. Replies
    2
    Views
    1,087

    Multicam SF User Manual

    I just acquires an a SF machine can anyone point me in the right direction for a user manual?

    Thanks in advance.

    Gary
  7. Need PLC Ladder logic programmer for a small project.

    Simple drilling machine with 4 air valves and a few limits. Could be by the hour or by the project.
  8. Replies
    0
    Views
    579

    Copley XCE drive and mach3

    Hi,
    I am building a 5x10’ CNC laser. I have two Copley XCE drives and Servo motors. Could any recommend a motion controller that will work with these drives and Mach3? Would ecat be best from the...
  9. I have a R2E3 with a boss 8 control. The...

    I have a R2E3 with a boss 8 control. The spindle makes a lot of noise is this normal. It gets warm but not hot.
  10. Replies
    1
    Views
    719

    Mitsubishi TR-6DA1 scmatic needed

    I have a bad Mitsubishi TR-6DA1 monitor on my cnc machine. If anyone has or can point me in the right direction for a scmatic please let me know. Or how to interface a video monitor.


    Gary
  11. Replies
    2
    Views
    812

    Acme Delrin nut source

    Does anyone have a god source for low cost ACME Delrin nuts. Looking for a more cos efective source that Roton. I may need 100 pcs.

    Thanks

    Gary
  12. Replies
    14
    Views
    2,761

    This cutter is for sale.

    I have decided to sell this cutter I have never used it. Anyone intersted please let me know.

    Gary
  13. Thread: BOSS 8 problem

    by gguidi
    Replies
    16
    Views
    2,317

    Power

    Hi,

    I have the same machine. I had a phase converter set up and I had the same problems. I added a variable frequency ac drive to run the spindle and am running the drives and the logic on 220...
  14. Replies
    1
    Views
    1,542

    Charge by the hour

    Charge by the time it takes to cut the job. Decide on a rate per hour that will cover your costs and time.

    Gary Guidi

    www.depronlasercutting.com
  15. Replies
    6
    Views
    2,566

    Chinese laser warranty Value

    If the chinese company that you purchased you laser had a US service center that stocked parts and could troubleshoot problems at board level what would it be worth to you in the price of the laser. ...
  16. Replies
    14
    Views
    2,761

    Extreme Foam Cutter

    I just finished my cnc foam cutter. Photos can be found at this linkhttp://www.depronlasercutting.com/foam.html

    I am running CeNeCe cutting at about 20

    Gary Guidi

    Depron Laser Cutting
  17. Replies
    4
    Views
    1,411

    Eb, It is "0" It might be loosing steps but...

    Eb,

    It is "0" It might be loosing steps but the error is so repeatable. If I block cut it returns to the correct "0" position. I am running 400 steps per rev with a 16tpi screw.

    I am...
  18. Replies
    4
    Views
    1,411

    GMFC help needed

    Hi, All

    I just finished my cnc foam cutter and have it running on foamworks
    well. I am deciding what software to purchase and am now trying GMFC.
    I have it running but after it makes a cut it...
  19. Thread: bridgeport r2e4

    by gguidi
    Replies
    10
    Views
    1,205

    Voltage?

    My R2E3 would only stat once in a while. It turned out the the incoming voltage was to high. You may want to see if it is taped right.
  20. Thread: Wire tension

    by gguidi
    Replies
    1
    Views
    1,072

    Wire tension

    Dose anyone know how tight the wire should be in pounds of pull. I am designing a wire tension system and need to know where to start.

    Thanks

    Gary

    Depron Laser Cutting...
  21. Thread: Post Help

    by gguidi
    Replies
    1
    Views
    535

    Post Help

    Hi, All

    I just purchased a Bridgeport with a boss 8 control. I drew a simple rectangle with a .5 radius on the corners. I am using right tool comp. I get two corners that cut correctly. 1 corner...
  22. Replies
    5
    Views
    798

    Milling a 1" hole in 1" 6061

    What is the best way to do this. I understand the sprial/pipe option. It is ok but is there any way to have it pick the center of the hole and have it start there? Rather than finding the center and...
  23. Thread: Boss 8 post

    by gguidi
    Replies
    1
    Views
    930

    Boss 8 post

    Could someone email a Onecnc post for a Bridgeport with a boss8 control or point me in the right direction.

    Thanks

    Gary Guidi

    [email protected]
  24. Replies
    57
    Views
    3,096

    Ashland MA Bridgeport Boss 8 help

    Hi,

    I am in Ashland MA I need someone to teach me a little about running a r2e3 Bridgeport with a Boss 8 control. Bobcad help would be great also. I have a CNC laser that I cut foam on so I do...
  25. Replies
    16
    Views
    2,168

    r2e3 Lifting holes

    I need to move one this week. Dose it have holes to lift with?

    Thanks Gary
  26. Thread: Points on arcs

    by gguidi
    Replies
    2
    Views
    1,449

    Points on arcs

    When I get files from some of my customers in DXF format I open them in Auctocad. On the arcs I have hundreds of points. When I bring the file into Mach 3 it takes forever and the gcode file is huge...
Results 1 to 26 of 26