529,653 active members*
3,326 visitors online*
Register for free
Login

Search:

Type: Posts; User: mbservice

Page 1 of 16 1 2 3 4

Search: Search took 0.01 seconds; generated 29 minute(s) ago.

  1. Re: Bridgport Interact Series 1 TNC 145 Control - Repair Needed

    Hi Danny
    Check your brushes and if they are OK maybe the servo card is playing up
  2. Thread: Fanuc 0TD

    by mbservice
    Replies
    3
    Views
    27

    Re: Fanuc 0TD

    What machine do you have?
    How are you measuring your offsets?
    Check what Al said as maybe an offset in your worksheet page
  3. Replies
    10
    Views
    101

    Re: Operator's message language

    if you post the machine type and model no it may be easier to assist as Dr Dos has already said it is upto the manufacturers
  4. Replies
    2
    Views
    74

    Re: Alarm 2010 Fanuc 18-T, Suggestions?

    Check 24v supply if hydraulics shutting down possibly due to lack of signal that they are on.
    The encoder requires 24v to activate as well
  5. Replies
    11
    Views
    111

    Re: Machine Parameters

    Best ones are "Please help I have a cnc lathe with Fanuc O and need parameters"
    If they posted a machine manufacturer and model it would be soooooo much easier
  6. Replies
    6
    Views
    125

    Re: ER2 alarm on Fanuc controller O-T

    please send or post pic of the alarm
  7. Replies
    1
    Views
    172

    Re: harrison Alpha 1350XS spindle bearings

    Pm me serial number
  8. Replies
    6
    Views
    125

    Change your batteries there is an alarm showing...

    Change your batteries there is an alarm showing at bottom of screen
  9. Re: After 2 month covid shutdown - 21T wont boot - 4 simultaneous screens of garbage

    Whereabouts are you as there maybe an engineer local to you on here
  10. Replies
    11
    Views
    104

    Re: Sinumerik 802c pasword help

    On some older Siemens there were different coloured keys to stop operators doing stuff they were not meant to private message me your email and ill send you a pic
  11. Re: After 2 month covid shutdown - 21T wont boot - 4 simultaneous screens of garbage

    check your 24v to the board
  12. Replies
    11
    Views
    104

    Re: Sinumerik 802c pasword help

    Try sunrise however it may have a keylock as well to stop any interference by operators
  13. Re: CNC Training given onsite ,Fanuc,Heidenhain,Siemens etc in the UK

    Private message me please
  14. Replies
    1
    Views
    177

    Re: Hardinge bridgeport 450 p3 user manual

    if you press tool change button it should recover itself make sure doors are closed
  15. Replies
    1
    Views
    147

    Re: Colchester harrison 1515xt

    private message me your serial number
  16. Replies
    13
    Views
    2,072

    Re: Colchester Tornado 200 Lathe parameters and diagnosis

    send me your email and serial number as not clear in picture
    There were different versions of 200 so would hate to send you incorrect ones
  17. Replies
    7
    Views
    623

    Re: Harrison 550S Alpha - Paramters

    Hi
    I'd advise you not to use them . they are similar as in X and Z positions but have completely different drive parameters and pmc parameters along with software due to 550 having different control...
  18. Re: Anyone have Harrison alpha 400 PLC and parameters?

    Private message me machine serial number and screen reference when it powers up bottom right
  19. Re: Doosan Puma 240 - Fan running even with Controller Off

    Hi Mike
    Re the fan either fit an outside switch on the wire to the fan or alternatively get a new one they are about £30 from RS Components over here
    Re the turret I believe it has a small...
  20. Thread: Please help

    by mbservice
    Replies
    2
    Views
    147

    Re: Please help

    Please send me a message with your program generated by fusion or post it on here
  21. Re: pls, is there a bar puller design, for pulling at rpm 0 ?

    Why can't you stop the spindle?
    I'd go for coolant operated one
  22. Re: Manual for Colchester Combi 3000 with Fanuc 210i-T control

    Have you set the I/O to 4 on the setting page and set the combi to look at the card and not at the setting folder&nbsp;<br>Private message me I have manuals&nbsp;
  23. Re: Manual for Colchester Combi 3000 with Fanuc 210i-T control

    Have you set the I/O to 4 on the setting page and set the combi to look at the card and not at the setting folder
    Private message me I have manuals
  24. Replies
    3
    Views
    724

    Re: Fanuc OTc 414 X axis detect error alarm

    have sent you a pm
  25. Replies
    3
    Views
    724

    Re: Fanuc OTc 414 X axis detect error alarm

    Did you check the encoder ?
  26. Re: 1337/5000 TNC155: Data in RAM but inaccessible

    Your batteries have failed
    When the parameters are loaded they would come up with a ? You would not be a me to go back it would come up with a ? Again
    Unless all the parameters are fully loaded
  27. Re: Bridgeport Interact 1 Mk2 with TNC 2500 missing 110V on wire 8 and 9 when power o

    nikos
    Did you check the overtravel switches
  28. Replies
    16
    Views
    4,642

    Re: Colchester 2000L

    What turret do you have ? Do you have a barfeed? What is your problem?
  29. Re: Bridgeport series 1 interact TNC 145 Gross positioning error B

    Check your speed parameters
  30. Replies
    13
    Views
    2,072

    Re: Colchester Tornado 200 Lathe parameters

    Hi Vlad
    Tornado 100 parameters will be close but not correct as there are different models and veraions of the machine you may cause damage to your drives please send me your email address in a...
Results 1 to 30 of 474
Page 1 of 16 1 2 3 4